AM69AX datasheet(8/299 Pages) TI

8 / 299 page

6 Terminal Configuration and Functions

6.1 Pin Diagrams

Note

The terms "ball", "pin", and "terminal" are used interchangeably throughout the document. An attempt

is made to use "ball" only when referring to the physical package.

For details on the pin diagram, see the Mechanical, Packaging, and Orderable Information section.

6.2 Pin Attributes

1. Ball Number: Ball numbers assigned to each terminal of the Ball Grid Array package.

2. Ball Name: Ball name assigned to each terminal of the Ball Grid Array package (this name is typically taken

from the primary MUXMODE 0 signal function).

3. Signal Name: Signal name of all dedicated and pin multiplexed signal functions associated with a ball.

Note

The Pin Attributes table, defines the SoC pin multiplexed signal function implemented at the

pin and does not define secondary multiplexing of signal functions implemented in device

subsystems. Secondary multiplexing of signal functions are not described in this table. For more

information on secondary multiplexed signal functions, see the respective peripheral chapter of

the device TRM.

4. Mux Mode: The MUXMODE value associated with each pin multiplexed signal function:

• MUXMODE 0 is the primary pin multiplexed signal function. However, the primary pin multiplexed signal

function is not necessarily the default pin multiplexed signal function.

• MUXMODE values 1 through 15 are possible for pin multiplexed signal functions. However, not all

MUXMODE values have been implemented. The only valid MUXMODE values are those defined as pin

multiplexed signal functions within the Pin Attributes table. Only valid values of MUXMODE can be used.

• Bootstrap defines SOC configuration pins, where the logic state applied to each pin is latched on the

rising edge of PORz_OUT. These input signal functions are fixed to their respective pins and are not

programmable via MUXMODE.

• An empty box or "-" means Not Applicable.

Note

• The value found in the MUX MODE AFTER RESET column defines the default pin multiplexed

signal function selected when MCU_PORz is deasserted.

• Configuring two pins to the same pin multiplexed signal function can yield unexpected results

and is not supported. This can be prevented with proper software configuration.

• Configuring a pad to an undefined multiplexing mode results in undefined behavior and must

be avoided.

5. Signal Type: Signal type and direction:

• I = Input

• O = Output

• OD = Output, with open-drain output function

• IO = Input, Output, or simultaneously Input and Output

• IOD = Input, Output, or simultaneously Input and Output, with open-drain output function

• IOZ = Input, Output, or simultaneously Input and Output, with three-state output function

• OZ = Output with three-state output function

• A = Analog

• CAP = LDO capacitor

• PWR = Power

• GND = Ground

6. I/O VOLTAGE VALUE: This column describes the IO voltage value (the corresponding power supply).

AM69A

SPRSP92 – FEBRUARY 2023

www.ti.com

Submit Document Feedback

Product Folder Links: AM69A

AM69AX 数据表(PDF) 8 Page - Texas Instruments

AM69AX 数据表(HTML) 8 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载

链接网址

AM69AX 数据表(PDF) 8 Page - Texas Instruments

AM69AX 数据表(HTML) 8 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表 下载

链接网址

数据表下载