| 数据搜索系统,热门电子元器件搜索 |
|
LTM8024 数据表(PDF) 18 Page - Analog Devices |
|
|
|||||||||||||||||||||||||||||
LTM8024 数据表(HTML) 18 Page - Analog Devices |
|
18 / 26 page ![]() LTM4709 18 Rev. 0 For more information www.analog.com a thorough laboratory evaluation replicates the simulated conditions with thermocouples within a controlled envi- ronment chamber while operating the device at the same power loss as simulated. An outcome of this process and due diligence yields a set of derating curves (see Figure 7 to Figure 13). After these laboratory tests have been performed and cor- related to the LTM4709 model, then the θJA is provided assuming approximately 100% of the power loss flows from the junction through the board into the ambient with no airflow or top-mounted heat sink. The load current derating curves are shown in Figure 7 to Figure 13. The maximum load current is achievable while increasing ambient temperature if the junction tempera- ture is less than 145°C, which is 5°C guard band from the maximum junction temperature of 150°C. When the ambient temperature reaches a point where the junction temperature is 145°C, then the load current is lowered to maintain the junction at 145°C while increasing the ambient temperature up to 140°C. The derating curves are plotted with three channels in parallel, total current starting at full load 9A, and the ambient temperature at 25°C. The input-to-output differential voltages are 200mV, 250mV, 300mV, 400mV, 500mV, 600mV, 700mV. These are chosen to include the lower and higher output voltage ranges. Thermal models are derived from several tempera- ture measurements in a controlled temperature chamber, along with thermal modeling analysis. The junction tem- peratures are monitored while the ambient temperature is increased with and without airflow. The decreased output current will decrease the internal module loss as ambient temperature is increased. Table 2 provides equivalent thermal resistances for with and without air- flow. LTpowerCAD offers an empirical thermal model for thermal estimation based on the EVAL-LTM4709-BZ evaluation board as well. The printed circuit board is a 1.6mm thick four layers board with two-ounce copper for all four layers. The PCB dimensions are 114mm × 124mm. APPLICATIONS INFORMATION Table 2. Derating Curve at Various VIN – VOUT DERATING CURVE VIN – VOUT (V) AIRFLOW (LFM) HEAT SINK θJA (°C/W) Figure 7 0.2 0 None 15 Figure 8 0.25 Figure 9 0.3 Figure 10 0.4 Figure 11 0.5 Figure 12 0.6 Figure 13 0.7 Figure 7 0.2 200 None 13.5 Figure 8 0.25 Figure 9 0.3 Figure 10 0.4 Figure 11 0.5 Figure 12 0.6 Figure 13 0.7 Figure 7 0.2 400 None 13 Figure 8 0.25 Figure 9 0.3 Figure 10 0.4 Figure 11 0.5 Figure 12 0.6 Figure 13 0.7 |
|
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |