 |
数据搜索系统，热门电子元器件搜索 |
|
|
数据搜索系统，热门电子元器件搜索 |
|
USB2502-HT 数据表(PDF) 18 Page - SMSC Corporation |
|
|
|||||||||||||||||||||||||||||
USB2502-HT 数据表(HTML) 18 Page - SMSC Corporation |
|
|
18 / 44 page  2-Port USB 2.0 Hub Controller Datasheet Revision 2.1 (12-06-06) 18 SMSC USB2502 DATASHEET When Dynamic Power switching is enabled, the Hub detects the availability of a local power source by monitoring the external SELF_PWR pin. If the Hub detects a change in power source availability, the Hub immediately disconnects and removes power from all downstream devices and disconnects the upstream port. The Hub will then re-attach to the upstream port as either a Bus-Powered Hub (if local-power in unavailable) or a Self-Powered Hub (if local power is available). This field is set by the OEM using either the SMBus or EEPROM interface options. 5.1.1.13 Over-Current Timer The time delay (in 2ms increments) for an over-current condition to persist before it is reported to the Host. This field is set by the OEM using either the SMBus or EEPROM interface options. 5.1.1.14 Self-Powered Max Power When in Self-Powered configuration, Sets value in 2mA increments. This field is set by the OEM using either the SMBus or EEPROM interface options. 5.1.1.15 Bus-Powered Max Power When in Bus-Powered configuration, Sets value in 2mA increments. This field is set by the OEM using either the SMBus or EEPROM interface options. 5.1.1.16 Self-powered Hub Controller Current When in Self-Powered configuration, Maximum current requirements of the Hub Controller in 2mA increments. This field is set by the OEM using either the SMBus or EEPROM interface options. 5.1.1.17 Bus-Powered Hub Controller Current When in Bus-Powered configuration, Maximum current requirements of the Hub Controller in 2mA increments. This field is set by the OEM using either the SMBus or EEPROM interface options. 5.1.1.18 Power-On Timer Time (in 2ms intervals) from the time power-on sequence begins on a port until power is good on that port. System software uses this value to determine how long to wait before accessing a powered-on port. This field is set by the OEM using either the SMBus or EEPROM interface options. 5.1.1.19 Power Switching Polarity The selection of active state “polarity” for the PRTPWR2 pin is made by a strapping option only. 5.1.2 VBus Detect According to Section 7.2.1 of the USB 2.0 Specification, a downstream port can never provide power to its D+ or D- pull-up resistors unless the upstream port’s VBUS is in the asserted (powered) state. The VBUS_DET pin on the Hub monitors the state of the upstream VBUS signal and will not pull-up the D+ or D- resistor if VBUS is not active. If VBUS goes from an active to an inactive state (Not Powered), Hub will remove power from the D+ or D- pull-up resistor within 10 seconds. |
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Chinese ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
