MB90F347CE datasheet(14/85 Pages) FUJITSU

14 / 85 page

MB90340E Series

(Continued)

Pin No.

Pin name

I/O

Circuit

type*3

Function

QFP100*1 LQFP100*2

P34

General purpose I/O pin. The register can be set to select

whether to use a pull-up resistor. This function is enabled either

in single-chip mode or when the hold function is disabled.

HRQ

Hold request input pin. This function is enabled when both the

external bus and the hold function are enabled.

OUT4

Waveform output pin for output compare.

P35

General purpose I/O pin. The register can be set to select

whether to use a pull-up resistor. This function is enabled either

in single-chip mode or when the hold function is disabled.

HAK

Hold acknowledge output pin. This function is enabled when

both the external bus and the hold function are enabled.

OUT5

Waveform output pin for output compare.

P36

General purpose I/O pin. The register can be set to select

whether to use a pull-up resistor. This function is enabled either

in single-chip mode or when the external ready function is

disabled.

RDY

External ready input pin. This function is enabled when both the

external bus and the external ready function are enabled.

OUT6

Waveform output pin for output compare.

P37

General purpose I/O pin. The register can be set to select

whether to use a pull-up resistor. This function is enabled either

in single-chip mode or when the clock output is disabled.

CLK

Clock output pin. This function is enabled when both the

external bus and clock output are enabled.

OUT7

Waveform output pin for output compare OCU7

13, 14

11, 12

P40, P41

General purpose I/O pins.

(devices with an S suffix in the part number and or

MB90V340E-101)

X0A , X1A

Oscillation pins for sub clock

(devices without an S suffix in the part number and or

MB90V340E-102)

VCC

⎯

Power (3.5 V to 5.5 V) input pin

VSS

⎯

GND pin

This is the power supply stabilization capacitor This pin should

be connected to a ceramic capacitor with a capacitance greater

than or equal to 0.1

µF.

P42

General purpose I/O pin.

IN6

Trigger input pin for input capture.

RX1

RX input pin for CAN1 Interface

(MB90F342E/F343E/F345E/341E/342E only)

INT9R

External interrupt request input pin

MB90F347CE 数据表(PDF) 14 Page - fujitsu semiconductor

MB90F347CE 数据表(HTML) 14 Page - fujitsu semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85

数据表下载

链接网址

MB90F347CE 数据表(PDF) 14 Page - fujitsu semiconductor

MB90F347CE 数据表(HTML) 14 Page - fujitsu semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85

数据表 下载

链接网址

数据表下载