 |
数据搜索系统，热门电子元器件搜索 |
|
|
数据搜索系统，热门电子元器件搜索 |
|
ST7LITE0X 数据表(PDF) 102 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
ST7LITE0X 数据表(HTML) 102 Page - STMicroelectronics |
|
|
102 / 125 page  ST7LITE0x, ST7LITESx 102/125 CONTROL PIN CHARACTERISTICS (Cont’d) Figure 75. RESET pin protection when LVD is enabled.1)2)3)4) Figure 76. RESET pin protection when LVD is disabled.1) Note 1: – The reset network protects the device against parasitic resets. – The output of the external reset circuit must have an open-drain output to drive the ST7 reset pad. Otherwise the device can be damaged when the ST7 generates an internal reset (LVD or watchdog). – Whatever the reset source is (internal or external), the user must ensure that the level on the RESET pin can go below the VIL max. level specified in section 13.9.1 on page 101. Otherwise the reset will not be taken into account internally. – Because the reset circuit is designed to allow the internal RESET to be output in the RESET pin, the user must en- sure that the current sunk on the RESET pin is less than the absolute maximum value specified for IINJ(RESET) in section 13.2.2 on page 83. Note 2: When the LVD is enabled, it is recommended not to connect a pull-up resistor or capacitor. A 10nF pull-down capacitor is required to filter noise on the reset line. Note 3: In case a capacitive power supply is used, it is recommended to connect a 1M Ω pull-down resistor to the RESET pin to discharge any residual voltage induced by the capacitive effect of the power supply (this will add 5µA to the power consumption of the MCU). Note 4: Tips when using the LVD: – 1. Check that all recommendations related to ICCCLK and reset circuit have been applied (see caution in Table 1 on page 7 and notes above) – 2. Check that the power supply is properly decoupled (100nF + 10µF close to the MCU). Refer to AN1709 and AN2017. If this cannot be done, it is recommended to put a 100nF + 1M Ω pull-down on the RESET pin. – 3. The capacitors connected on the RESET pin and also the power supply are key to avoid any start-up marginality. In most cases, steps 1 and 2 above are sufficient for a robust solution. Otherwise: replace 10nF pull-down on the RESET pin with a 5µF to 20µF capacitor.” Note 5: Please refer to See “Illegal Opcode Reset” on page 79. for more details on illegal opcode reset conditions 0.01 µF ST72XXX PULSE GENERATOR Filter RON VDD INTERNAL RESET RESET EXTERNAL Required 1M Ω Optional (note 3) WATCHDOG LVD RESET ILLEGAL OPCODE 5) 0.01 µF EXTERNAL RESET CIRCUIT USER Required ST72XXX PULSE GENERATOR Filter RON VDD INTERNAL RESET WATCHDOG ILLEGAL OPCODE 5) 1 |
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Chinese ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
