ST7LITE0X datasheet(41/125 Pages) STMICROELECTRONICS

41 / 125 page

ST7LITE0x, ST7LITESx

41/125

POWER SAVING MODES (Cont’d)

9.4.2 HALT MODE

The HALT mode is the lowest power consumption

mode of the MCU. It is entered by executing the

‘HALT’ instruction when active halt mode is disa-

bled.

The MCU can exit HALT mode on reception of ei-

ther a specific interrupt (see Table 6, “Interrupt

Mapping,” on page 31) or a RESET. When exiting

HALT mode by means of a RESET or an interrupt,

the oscillator is immediately turned on and the 256

CPU cycle delay is used to stabilize the oscillator.

After the start up delay, the CPU resumes opera-

tion by servicing the interrupt or by fetching the re-

set vector which woke it up (see Figure 27).

When entering HALT mode, the I bit in the CC reg-

ister is forced to 0 to enable interrupts. Therefore,

if an interrupt is pending, the MCU wakes immedi-

ately.

In HALT mode, the main oscillator is turned off

causing all internal processing to be stopped, in-

cluding the operation of the on-chip peripherals.

All peripherals are not clocked except the ones

which get their clock supply from another clock

generator (such as an external or auxiliary oscilla-

tor).

The compatibility of Watchdog operation with

HALT mode is configured by the “WDGHALT” op-

tion bit of the option byte. The HALT instruction

when executed while the Watchdog system is en-

abled, can generate a Watchdog RESET (see sec-

tion 15.1 on page 114 for more details).

Figure 26. HALT Timing Overview

Figure 27. HALT Mode Flow-chart

Notes:

1. WDGHALT is an option bit. See option byte sec-

tion for more details.

2. Peripheral clocked with an external clock source

can still be active.

3. Only some specific interrupts can exit the MCU

from HALT mode (such as external interrupt). Re-

fer to Table 6, “Interrupt Mapping,” on page 31 for

more details.

4. Before servicing an interrupt, the CC register is

pushed on the stack. The I bit of the CC register is

set during the interrupt routine and cleared when

the CC register is popped.

5. If the PLL is enabled by option byte, it outputs

the clock after a delay of tSTARTUP (see Figure 12).

HALT

RUN

256 CPU CYCLE

DELAY

RESET

INTERRUPT

HALT

INSTRUCTION

FETCH

VECTOR

[Active Halt disabled]

HALT INSTRUCTION

RESET

INTERRUPT 3)

CPU

OSCILLATOR

PERIPHERALS 2)

IBIT

OFF

FETCH RESET VECTOR

OR SERVICE INTERRUPT

CPU

OSCILLATOR

PERIPHERALS

IBIT

OFF

X 4)

CPU

OSCILLATOR

PERIPHERALS

IBITS

X 4)

256 CPU CLOCK CYCLE

DELAY

WATCHDOG

ENABLE

DISABLE

WDGHALT 1)

WATCHDOG

RESET

(Active Halt disabled)

ST7LITE0X 数据表(PDF) 41 Page - STMicroelectronics

ST7LITE0X 数据表(HTML) 41 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载

链接网址

ST7LITE0X 数据表(PDF) 41 Page - STMicroelectronics

ST7LITE0X 数据表(HTML) 41 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表 下载

链接网址

数据表下载