USB97C102 datasheet(9/80 Pages) SMSC

9 / 80 page

SMSC DS – USB97C102

Page 9

Rev. 03/23/2000

FUNCTIONAL DESCRIPTION

The USB97C102 incorporates a USB Serial Interface Engine (SIE), 8051 Microcontroller Unit (MCU), Serial Interface

Engine DMA (SIEDMA), a programmable 8237 ISA bus DMA controller (ISADMA), 4K bytes of SRAM for data stream

buffering, and a patented MMU (Memory Management Unit) to dynamically manage buffer allocation. The semi-

automatic nature of the SIEDMA, ISADMA, and MMU blocks frees the MCU to provide enumeration, protocol and

power management. A bus arbiter integrated into the MMU assures that transparent access between the SIEDMA,

ISADMA, and MCU to the SRAM occurs.

Serial Interface Engine (SIE)

The SIE is a USB low-level protocol interpreter. The SIE controls the USB bus protocol, packet generation/extraction,

parallel-to-serial/serial-to-parallel conversion, CRC coding/decoding, bit stuffing, and NRZI coding/decoding.

The SIE can be dynamically configured as having any combination of 0-16 transmit, and 0-16 receive endpoints, for

up to 4 independent addresses. There are 3 alternate and one local address. The alternate addresses, for example,

can be used for Hub addresses. The SIE can also "Receive All Addresses" for bus snooping.

Micro Controller Unit (MCU)

The 8051 embedded controller is a static CMOS MCU which is fully software compatible with the industry standard

Intel 80C51 micro-controller. All internal registers of the USB97C102 blocks are mapped into the external memory

space of the MCU.

A detailed description of the microcontroller’s internal registers and instruction set can be found in the “USB97C102

Programmer’s Reference Guide”.

SIEDMA

This is a simplified DMA controller, which automatically transfers data between SIE and SRAM via MMU control. The

SIEDMA appends a status header containing frame number, endpoint, and byte count to each incoming packet

before notifying the MCU of its arrival. This block’s operation is transparent to the firmware.

Memory Management Unit (MMU) Register Description

This patented MMU consists of a 4k buffer RAM which is allocated in 32 pages of 128 bytes. Packets can be

allocated with up to 10 pages each (1280 bytes). The buffer can therefore concurrently hold up to 32 packets with a

64 byte payload. For isochronous pipes, it can hold 3 packets with a 1023 byte payload each, and still have room for

two more 64 byte packets.

This block supports 16 independent transmit FIFO queues (one for each endpoint), and a single receive queue. Each

endpoint can have up to five transmit packets queued.

The receive queue can accept 32 packets of any size

combination before forcing the host to back off.

The arbiter makes the single-ported buffer RAM appear to be simultaneously available to the MCU, the four channels

of the ISADMA, and the SIEDMA for receiving and transmitting packets.

ISADMA

This is an industry standard 8237 DMA controller to transfer data between the ISA bus and the SRAM under MMU

control.

This DMA contains status and control registers which can be accessed and programmed by the 8051

controller. The 8237 can run at 2, 4, or 8 MHz internally, or via an external clock to synchronize it with another

source.

SGDMA

A four channel Scatter-Gather DMA will run the 8237 DMA controller once the MCU indicates which packets to

transfer. The SGDMA performs scattering/gathering operations from the MMU to/from the external ISA memory.

It also allows ISA device to/from MMU transfer.

Applications

The USB97C102 enables entirely new I/O applications, as well as new form factors for existing Legacy I/O

applications. PC98 compliance encourages the elimination ofDMA, IRQ and addressing conflicts via total on-board

ISA elimination. With the USB97C102, the ISA bus can be eliminated from motherboards without sacrificing the huge

infrastructure of Legacy I/O ports. By moving these devices to the flexible USB bus, new form factors such as monitor

peripheral clusters are also possible (mouse, keyboard, serial, parallel ports in a USB connected monitor). PC

system designers are no longer constrained by the physical borders of the motherboard. The USB97C102 is ideal for

USB peripherals which require considerable bandwidth, such as floppy drives, audio, IR, etc. The following block

diagrams illustrate these applications.

USB97C102 数据表(PDF) 9 Page - SMSC Corporation

USB97C102 数据表(HTML) 9 Page - SMSC Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80

数据表下载