ST10F276 datasheet(29/229 Pages) STMICROELECTRONICS

29 / 229 page

ST10F276

Internal Flash memory

29/229

4.4.2

Flash control register 0 high

The Flash control register 0 high (FCR0H) together with the Flash control register 0 Low

(FCR0L) is used to enable and to monitor all the write operations for both the Flash

modules. The user has no access in write mode to the Test-Flash (B0TF). Besides, test-

Flash block is seen by the user in Bootstrap mode only.

LOCK

Flash registers access locked

When this bit is set, it means that the access to the Flash Control Registers FCR0H/-

FCR1H/L, FDR0H/L-FDR1H/L, FARH/L and FER is locked by the FPEC: any read

access to the registers will output invalid data (software trap 009Bh) and any write

access will be ineffective. LOCK bit is automatically set when the Flash bit WMS is set.

This is the only bit the user can always access to detect the status of the Flash: once it

is found low, the rest of FCR0L and all the other Flash registers are accessible by the

user as well.

Note that FER content can be read when LOCK is low, but its content is updated only

when also BSY bits are reset.

BSY(1:0)

Bank 1:0 Busy (IFLASH)

These bits indicate that a write operation is running in the corresponding Bank of

IFLASH. They are automatically set when bit WMS is set. When these bits are set

every read access to the corresponding Bank will output invalid data (software trap

009Bh), while every write access to the Bank will be ignored. At the end of the write

operation or during a Program or Erase Suspend these bits are automatically reset

and the Bank returns to read mode. After a Program or Erase Resume these bits are

automatically set again.

Table 6.

Flash control register 0 low (continued)

Bit

Function

FCR0H (0x0E 0002)

FCR

Reset value: 0000h

987

65432

WMS

SUSP

WPG DWPG

SER

Reserved

SPR

SMOD

Reserved

Table 7.

Flash control register 0 high

Bit

Function

SMOD

Select module

If this bit is reset, the Write Operation is performed on XFLASH Module; if this bit is

set, the Write Operation is performed on IFLASH Module. SMOD bit is automatically

reset at the end of the Write operation.

SPR

Set protection

This bit must be set to select the Set Protection operation. The Set Protection

operation allows to program 0s in place of 1s in the Flash Non Volatile Protection

Registers. The Flash Address in which to program must be written in the FARH/L

registers, while the Flash Data to be programmed must be written in the FDR0H/L

before starting the execution by setting bit WMS. A sequence error is flagged by bit

SEQER of FER if the address written in FARH/L is not in the range 0x0EDFB0-

0x0EDFBF. SPR bit is automatically reset at the end of the Set Protection operation.

ST10F276 数据表(PDF) 29 Page - STMicroelectronics

ST10F276 数据表(HTML) 29 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载