PPC440SP-RNC667C datasheet(12/85 Pages) AMCC

12 / 85 page

PowerPC 440SP Embedded Processor

AMCC Proprietary

Revision 1.23 - Sept 26, 2006

Data Sheet

• 24-bit address, 16MB address space

• Peripheral Device pacing with external “Ready”

• Latch data on Ready, synchronous or asynchronous

• Programmable access timing per device

– 256 Wait States for non-burst

– 32 Burst Wait States for first access and up to 8 Wait States for subsequent accesses

– Programmable CSon, CSoff relative to address

– Programmable OEon, WEon, WEoff (1 to 4 clock cycles) relative to CS

• Programmable address mapping

Ethernet Controller Interface

The Ethernet support interfaces to the physical layer, but the PHY is not included on the chip.

Features include:

• One 10/100/1000 interface running in full- and half-duplex modes

– One full Media Independent Interface (MII) with 4-bit parallel data transfer

– One Gigabit Media Independent Interface (GMII)

I2O/DMA Controller

The I20/DMA controller provides support for I20 messaging and two DMA controllers (DMA0 and DMA1). I2O

manages message frame address (MFA) FIFOs or queues in memory in response to I2O register reads and writes

and transfers message frames. The DMAs provide normal memory access support to ease the CPU burden.

I2O features include:

• I2O pull- and push-messaging methods

• Dynamic message frame size

• Programmable FIFO size (4096 64-bit MFAs maximum)

• 64-bit and 32-bit MFA sizes

• Three interrupt gathering methods

• Registered MFA prefetch and posting

• 32-bit inbound and outbound doorbell registers

• Four 32-bit scratch pad registers

DMA features include:

• Programmable Command Pointer FIFO and Completion FIFO size (up to 2048 DMA operations queued)

• 512-byte/1KB buffering for DMA0/DMA1

• Simultaneous fill and drain (PLB read/write pipelining)

• Any source PLB address to any destination address

• No memory alignment restrictions on source or destination

• 32-byte command descriptor block

• Maximum transfer size of 16MB

• 64-bit addressing

• Prefetch indicators for PCI-X buffer management (DMA1 only)

Optional RAID 5 and RAID 6 Acceleration Hardware

The 440SP provides integrated acceleration hardware that implements high throughput RAID 5 and RAID 6

algorithms to compute the single parity P for RAID 5, and dual parity P & Q for RAID 6. RAID 5 is used to recover

data in the case of a single disk drive failure, and RAID 6 provides for data recovery if two disk drives fail.

The 440SP offers a choice of two XOR engines for computing the P parity. The first choice is available with the

XOR/DMA2 acceleration unit and is used for RAID 5. The second choice for XOR parity computation, along with

the RAID 6 Galois Field GF(28)-based polynomial computations, resides inside the Memory Queue functional block

PPC440SP-RNC667C 数据表(PDF) 12 Page - Applied Micro Circuits Corporation

PPC440SP-RNC667C 数据表(HTML) 12 Page - Applied Micro Circuits Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85

数据表下载