| 数据搜索系统,热门电子元器件搜索 |
|
CC1070-RTR1 数据表(PDF) 24 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
CC1070-RTR1 数据表(HTML) 24 Page - Texas Instruments |
|
24 / 57 page ![]() CC1070 SWRS043A Page 24 of 54 FSK frequency deviation is programmed in the DEVIATION register. The deviation programming is divided into a mantissa (TXDEV_M[3:0]) and an exponent (TXDEV_X[2:0]). Generally REF_DIV should be as low as possible but the following requirements must be met [] MHz f f c ref 256 8304 . 9 > ≥ in the frequency band 402 – 470 MHz, and [] MHz f f c ref 512 8304 . 9 > ≥ in the frequency band 804 – 940 MHz. The PLL output frequency equation above gives the carrier frequency, fc , in transmit mode (center frequency). The two FSK modulation frequencies are given by: f0 = fc − fdev f1 = fc + fdev where fdev is set by the DEVIATION register: ) 16 _ ( 2 _ − ⋅ ⋅ = X TXDEV ref dev M TXDEV f f in the frequency band 402 - 470 MHz, and ) 15 _ ( 2 _ − ⋅ ⋅ = X TXDEV ref dev M TXDEV f f in the frequency band 804 - 940 MHz. OOK (On-Off Keying) is used if TXDEV_M[3:0] = 0000. The TX_SHAPING bit in the DEVIATION register controls Gaussian shaping of the modulation signal. 11.1 Dithering Spurious signals will occur at certain frequencies depending on the division ratios in the PLL. To reduce the strength of these spurs, a common technique is to use a dithering signal in the control of the frequency dividers. Dithering is activated by setting the DITHER bit in the FREQ_0 registers. It is recommended to use the dithering in order to achieve the best possible performance. 12 Transmitter 12.1 FSK Modulation Formats The data modulator can modulate FSK, which is a two level FSK (Frequency Shift Keying), or GFSK, which is a Gaussian filtered FSK with BT = 0.5. The purpose of the GFSK is to make a more bandwidth efficient system. The modulation and the Gaussian filtering are done internally in the chip. The TX_SHAPING bit in the DEVIATION register enables the GFSK. GFSK is recommended for narrowband operation. 12.2 OOK Modulation The data modulator can also do OOK (On- Off Keying) modulation. OOK is an ASK (Amplitude Shift Keying) modulation using 100% modulation depth. OOK modulation is enabled by setting TXDEV_M[3:0] = 0000 in the DEVIATION register. |
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |