SN260 datasheet(46/88 Pages) STMICROELECTRONICS

46 / 88 page

EmberZNet serial protocol

SN260

46/88

EMBER_SIM_EEPROM_ERASE_PAGE_GREEN

0x43

Simulated EEPROM is telling the application that there is

at least one flash page to be erased. GREEN status

means the current page has not filled above the

ERASE_CRITICAL_THRESHOLD

. The application should

call the function halSimEepromErasePage() when it

can to erase a page.

EMBER_SIM_EEPROM_ERASE_PAGE_RED

0x44

Simulated EEPROM is telling the application that there is

at least one flash page to be erased. RED status means

the current page has filled above the

ERASE_CRITICAL_THRESHOLD

. Due to the shrinking

availability of write space, there is a danger of data loss.

The application must call the function

halSimEepromErasePage()

as soon as possible to

erase a page.

EMBER_SIM_EEPROM_FULL

0x45

Simulated EEPROM has run out of room to write any

new data and the data trying to be set has been lost.

This error code is the result of ignoring the

SIM_EEPROM_ERASE_PAGE_RED

error code. The

application must call the function

halSimEepromErasePage()

to make room for any

further calls to set a token.

EMBER_SIM_EEPROM_FLASH_WRITE_

FAILED

0x46

A fatal error has occurred while trying to write data to the

Flash and the write verification has failed. The data in

the flash cannot be trusted after this error, and it is

possible this error is the result of exceeding the life

cycles of the flash.

EMBER_SIM_EEPROM_INIT_1_FAILED

0x47

Attempt 1 to initialize the simulated EEPROM has failed.

This failure means the information already stored in

Flash (or a lack thereof), is fatally incompatible with the

token information compiled into the code image being

run.

EMBER_SIM_EEPROM_INIT_2_FAILED

0x48

Attempt 2 to initialize the simulated EEPROM has failed.

This failure means Attempt 1 failed, and the token

system failed to properly reload default tokens and reset

the simulated EEPROM.

EMBER_SIM_EEPROM_INIT_3_FAILED

0x49

Attempt 3 to initialize the simulated EEPROM has failed.

This failure means one or both of the tokens

TOKEN_MFG_NVDATA_VERSION

TOKEN_STACK_NVDATA_VERSION

were incorrect and

the token system failed to properly reload default tokens

and reset the simulated EEPROM.

EMBER_ERR_TOKEN_UNKNOWN

0x4B

An unknown flash token was specified.

EMBER_ERR_TOKEN_EXISTS

0x4C

Could not create new flash token because it already

exists.

EMBER_ERR_TOKEN_INVALID_SIZE

0x4D

An incorrect size was specified when retrieving token

data.

EMBER_ERR_TOKEN_READ_ONLY

0x4E

Couldn't write token because it is marked read-only.

EMBER_ERR_BOOTLOADER_TRAP_

TABLE_BAD

0x58

Bootloader received an invalid message (failed attempt

to go into bootloader).

Table 30.

EmberStatus (continued)

Structure

Field

Description

SN260 数据表(PDF) 46 Page - STMicroelectronics

SN260 数据表(HTML) 46 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88

数据表下载