CLC030 datasheet(21/29 Pages) NSC

21 / 29 page

Device Operation (Continued)

control register instead of the multi-function I/O port, bit 7,

the I/O port bit must be remapped to another bit in the control

registers. Remapping to a read-only function is recom-

mended to avoid possible conflicting data being written into

the remapped location.

The Pass/Fail bit indicates the result of running the built-in

self-test. This bit is a logic-1 for a pass condition. The bit is

mapped to I/O port bit 6 in the default condition.

VIDEO INFO 0 REGISTER (Address 0Eh)

The NSP (New Sync Position) bit indicates that a new or

out-of-place TRS character has been detected in the input

data. This bit is set to a logic-1 and remains set for at least

one horizontal line period or unless re-activated by a subse-

quent new or out-of-place TRS. It is reset by an EAV TRS

character.

The EAV (end of active video) and SAV (start of active video)

bits track the occurrence of the corresponding TRS charac-

ters.

Lock Detect is registered as a control signal and is a logic-1

when the PLL is locked and a valid format has been de-

tected. This bit may be programmed as an output on the

multi-function I/O port. This bit is mapped to I/O port bit 4 in

the default condition. This function also includes logic to

check the stability of the device after the digital logic reset is

released following PLL lock. If the system is not fully stable,

the logic is automatically reset. LOCK DETECT also com-

bines the function of indicating that the CLC030 has de-

tected the video format being received. This format detect

function involves determination of the major raster param-

eters such as line length, number of video lines in a frame,

and so forth. This is done so that information like line num-

bering can be correctly inserted. The PLL itself will have

locked in about 50 microseconds (HD rates, 150 microsec-

onds for SD) or less; however, resolution of all raster param-

eters may take the majority of a frame.

The VPG Filter Enable bit when set enables operation of the

Video Pattern Generator filter. Operation of this filter causes

the insertion of transition codes in the chroma and luma data

of color bar test patterns where these patterns change from

one bar to the next. This filter reduces the magnitude of

out-of-band frequency products which can be produced by

abrupt transitions in the chroma and luma data when fed to

D-to-A converters and picture monitors. The default condi-

tion of this bit is reset (off).

A method by which the occurrence of pathological data

patterns can be prevented has been proposed for SD for-

mats. The CLC030 implements this process for SD formats.

The Dither Enable and Vertical Dither Enable bits control

operation of pseudo-random dithering applied to the two

LSBs of the video data. Dithering is applied to active video

data when the Dither Enable bit is set. When the Vertical

Dither Enable bit is set, dithering is applied to that portion of

the video line corresponding to active video for lines in the

vertical blanking interval.

I/O PIN 0 THROUGH 7 CONFIGURATION REGISTERS

(Addresses 0Fh through 16h)

The Multi-function I/O Bus Pin Configuration registers are

used to map the bits of the multi-function I/O port to selected

bits of the Configuration and Control Registers. Table 6

details the available Configuration and Control register bit

functions that may be mapped to the port and their corre-

sponding mapping addresses. Pin # SEL[5] in each register

indicates whether the port pin is input or output. The port pin

will be an input when this bit is set and an output when reset.

Input-only functions may not be configured as outputs and

vice versa. The remaining lower-order five address bits dis-

tinguish the particular function.

Example: Program, via the AD port, I/O port bit 0 as output

for the CRC Luma Error bit in the control registers.

Set ANC/CTRL to a logic-low.

Set RD/WR to a logic-low.

Present 00Fh to AD[9:0] as the I/O PIN 0 CONFIG

Toggle ACLK.

Present 310h to AD[9:0] as the register data, the bit

address of the CRC Luma Error bit in the control regis-

ters.

Toggle ACLK.

TEST MODE 0 REGISTER (Address 55h)

The four bits of this register are intended for use as test

mode functions. They are not normal operating modes. The

bits may be set (enabled) or reset (disabled) by writing to the

default ON condition.

The Scrambler_Enable bit enables operation of the SMPTE

scrambler function. This bit is normally ON.

The NRZI_Enable bit enables operation of the NRZ-to-NRZI

conversion function. This bit is normally ON.

The LSB_Clipping bit enables operation of the LSB clipping

function. This bit is normally ON.

The Sync_Detect_Enable bit enables operation of the TRS

detector function. This bit is normally ON.

CLC030 数据表(PDF) 21 Page - National Semiconductor (TI)

CLC030 数据表(HTML) 21 Page - National Semiconductor (TI)

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29

数据表下载