M29W400 datasheet(12/34 Pages) STMICROELECTRONICS

12 / 34 page

Toggle Bit (DQ6). When Programming or Erasing

operations are in progress, successive attempts to

read DQ6 will output complementary data. DQ6 will

toggle following toggling of either G, or E when G

is low. The operation is completed when two suc-

cessive reads yield the same output data. The next

read will output the bit last programmedor a ’1’after

erasing. The toggle bit DQ6 is valid only during

P/E.C. operations, that is after the fourth W pulse

for programming or after the sixth W pulse for

Erase. If the blocks selected for erasure are pro-

tected, DQ6 will toggle for about 100

µs and then

return back to Read. DQ6 will be set to ’1’ if a Read

operation is attempted on an Erase Suspendblock.

When erase is suspended DQ6 will toggle during

programming operations in a block different to the

block in Erase Suspend. Either E or G toggling will

cause DQ6 to toggle. See Figure 12 for Toggle Bit

flowchart and Figure 13 for Toggle Bit waveforms.

Toggle Bit (DQ2). This toggle bit, together with

DQ6, can be used to determine the device status

during the Erase operations.It can also be used to

identify the block being erased. During Erase or

Erase Suspend a read from a block being erased

will cause DQ2 to toggle. A read from a block not

being erased will set DQ2 to ’1’ during erase and

to DQ2 during Erase Suspend. During Chip Erase

a read operation will cause DQ2 to toggle as all

blocks are being erased. DQ2 will be set to ’1’

during program operation and when erase is com-

plete. After erase completion and if the error bit

DQ5 is set to ’1’, DQ2 will toggle if the faulty block

is addressed.

Error Bit (DQ5). This bit is set to ’1’ by the P/E.C.

when there is a failure of programming, block

erase, or chip erase that results in invalid data in

the memory block. In case of an error in block erase

or program, the block in which the error occured or

to which the programmed data belongs, must be

discarded. The DQ5 failure condition will also ap-

pear if a user tries to program a ’1’ to a location that

is previously programmed to ’0’. Other Blocks may

stillbe used. The error bit resets after a Read/Reset

(RD) instruction. In case of success of Program or

Erase, the error bit will be set to ’0’ .

Erase Timer Bit (DQ3). This bit is set to ’0’ by the

P/E.C. when the last block Erase command has

been entered to the Command Interface and it is

awaiting the Erase start. When the erase timeout

period is finished, after 50

µsto 90µs, DQ3 returns

to ’1’.

Coded Cycles

The two Coded cycles unlock the Command Inter-

face. They are followed by an input command or a

confirmation command. The Coded cycles consist

of writing the data AAh at address AAAAh in the

Byte-wide configuration and at address 5555h in

the Word-wide configuration during the first cycle.

During the second cycle the Coded cycles consist

of writing the data 55h at address 5555h in the

Byte-wide configuration and at address 2AAAh in

the Word-wide configuration. In the Byte-wide con-

figuration the address lines A–1 to A14 are valid, in

Word-wide A0 to A14 are valid, other address lines

are ’don’t care’. The Coded cycles happen on first

and second cycles of the command write or on the

fourth and fifth cycles.

Instructions

See Table 8.

Read/Reset (RD) Instruction. The Read/Reset

instruction consists of one write cycle giving the

command F0h. It can be optionally precededby the

two Coded cycles. Subsequentread operationswill

read the memory array addressed and output the

data read. A wait state of 10

µs is necessary after

Read/Reset prior to any valid read if the memory

was in an Erase mode when the RD instruction is

given.

Auto Select (AS) Instruction. This instruction

uses the two Coded cycles followed by one write

cycle giving the command 90h to address AAAAh

in the Byte-wide configuration or address 5555h in

the Word-wide configuration for command set-up.

A subsequent read will output the manufacturer

code and the device code or the block protection

status depending on the levels of A0 and A1. The

manufacturer code, 20h, is output when the ad-

dresses lines A0 and A1 are Low, the device code,

EEh for Top Boot, EFh for Bottom Boot is output

when A0 is High with A1 Low.

The AS instruction also allows access to the block

protection status.After giving the AS instruction, A0

is set to VIL with A1 at VIH, while A12-A17 define

the address of the block to be verified. A read in

these conditions will output a 01h if the block is

protected and a 00h if the block is not protected.

Mode

DQ7

DQ6

DQ2

Program

DQ7

Toggle

Erase

Toggle

Note 1

Erase Suspend Read

(in Erase Suspend

block)

Toggle

Erase Suspend Read

(outside Erase Suspend

block)

DQ7

DQ6

DQ2

Erase Suspend Program

DQ7

Toggle

N/A

Note: 1. Toggle if the address is within a block being erased.

’1’ if the address is within a block not being erased.

Table 10. Polling and Toggle Bits

12/34

M29W400T, M29W400B

M29W400 数据表(PDF) 12 Page - STMicroelectronics

M29W400 数据表(HTML) 12 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34

数据表下载

链接网址

M29W400 数据表(PDF) 12 Page - STMicroelectronics

M29W400 数据表(HTML) 12 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34

数据表 下载

链接网址

数据表下载