PSD934210MIT datasheet(13/89 Pages) STMICROELECTRONICS

13 / 89 page

13/89

PSD834F2V

Note: 1. The pin numbers in this table are for the PLCC package only. See the package information, on page 83 onwards, for pin numbers

on other package types.

2. These functions can be multiplexed with other functions.

PSD REGISTER DESCRIPTION AND ADDRESS OFFSET

Table 6 shows the offset addresses to the PSD

registers relative to the CSIOP base address. The

CSIOP space is the 256 bytes of address that is al-

located by the user to the internal PSD registers.

Table 6 provides brief descriptions of the registers

in CSIOP space. The following section gives a

more detailed description.

PC5

I/O

PC5 pin of Port C. This port pin can be configured to have the following functions:

1. MCU I/O – write to or read from a standard output or input port.

2. CPLD macrocell (McellBC5) output.

3. Input to the PLDs.

4. TDI input2 for the JTAG Serial Interface.

This pin can be configured as a CMOS or Open Drain output.

PC6

I/O

PC6 pin of Port C. This port pin can be configured to have the following functions:

1. MCU I/O – write to or read from a standard output or input port.

2. CPLD macrocell (McellBC6) output.

3. Input to the PLDs.

4. TDO output2 for the JTAG Serial Interface.

This pin can be configured as a CMOS or Open Drain output.

PC7

I/O

PC7 pin of Port C. This port pin can be configured to have the following functions:

1. MCU I/O – write to or read from a standard output or input port.

2. CPLD macrocell (McellBC7) output.

3. Input to the PLDs.

4. DBE – active Low Data Byte Enable input from 68HC912 type MCUs.

This pin can be configured as a CMOS or Open Drain output.

PD0

I/O

PD0 pin of Port D. This port pin can be configured to have the following functions:

1. ALE/AS input latches address output from the MCU.

2. MCU I/O – write or read from a standard output or input port.

3. Input to the PLDs.

4. CPLD output (External Chip Select).

PD1

I/O

PD1 pin of Port D. This port pin can be configured to have the following functions:

1. MCU I/O – write to or read from a standard output or input port.

2. Input to the PLDs.

3. CPLD output (External Chip Select).

4. CLKIN – clock input to the CPLD macrocells, the APD Unit’s Power-down counter, and

the CPLD AND Array.

PD2

I/O

PD2 pin of Port D. This port pin can be configured to have the following functions:

1. MCU I/O – write to or read from a standard output or input port.

2. Input to the PLDs.

3. CPLD output (External Chip Select).

4. PSD Chip Select Input (CSI). When Low, the MCU can access the PSD memory and I/

O. When High, the PSD memory blocks are disabled to conserve power.

VCC

15, 38

Supply Voltage

GND

1, 16,

Ground pins

Pin Name

Type

Description

PSD934210MIT 数据表(PDF) 13 Page - STMicroelectronics

PSD934210MIT 数据表(HTML) 13 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89

数据表下载

链接网址

PSD934210MIT 数据表(PDF) 13 Page - STMicroelectronics

PSD934210MIT 数据表(HTML) 13 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89

数据表 下载

链接网址

数据表下载