MPC8313ECVRGDDB datasheet(55/100 Pages) FREESCALE

55 / 100 page

MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 2.1

Freescale Semiconductor

Figure 46 provides the AC test load for the I2C.

Figure 46. I2C AC Test Load

Figure 47 shows the AC timing diagram for the I2C bus.

Figure 47. I2C Bus AC Timing Diagram

Data hold time:

CBUS compatible masters

I2C bus devices

tI2DXKL

—

0.93

μs

Fall time of both SDA and SCL signals5

tI2CF

—

300

Setup time for STOP condition

tI2PVKH

0.6

—

μs

Bus free time between a STOP and START condition

tI2KHDX

1.3

—

μs

Noise margin at the LOW level for each connected device (including

hysteresis)

VNL

0.1

× NVDD

—V

Noise margin at the HIGH level for each connected device (including

hysteresis)

VNH

0.2

× NVDD

—V

Notes:

1. The symbols used for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state)(reference)(state) for

inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tI2DVKH symbolizes I

2C timing (I2)

with respect to the time data input signals (D) reach the valid state (V) relative to the tI2C clock reference (K) going to the high

(H) state or setup time. Also, tI2SXKL symbolizes I

2C timing (I2) for the time that the data with respect to the start condition

(S) went invalid (X) relative to the tI2C clock reference (K) going to the low (L) state or hold time. Also, tI2PVKH symbolizes I

timing (I2) for the time that the data with respect to the stop condition (P) reaching the valid state (V) relative to the tI2C clock

reference (K) going to the high (H) state or setup time. For rise and fall times, the latter convention is used with the appropriate

letter: R (rise) or F (fall).

2. The MPC8313E provides a hold time of at least 300 ns for the SDA signal (referred to the VIHmin of the SCL signal) to bridge

the undefined region of the falling edge of SCL.

3. The maximum tI2DVKH has only to be met if the device does not stretch the LOW period (tI2CL) of the SCL signal.

4. CB = capacitance of one bus line in pF.

5. The MPC8313E does not follow the

I2C-BUS Specifications, Version 2.1, regarding the tI2CF AC parameter.

Table 50. I2C AC Electrical Specifications (continued)

All values refer to VIH (min) and VIL (max) levels (see Table 49).

Parameter

Symbol1

Min

Max

Unit

Output

Z0 = 50 Ω

NVDD/2

RL = 50 Ω

SDA

SCL

tI2CF

tI2SXKL

tI2CL

tI2CH

tI2DXKL

tI2DVKH

tI2SXKL

tI2SVKH

tI2KHKL

tI2PVKH

tI2CR

tI2CF

MPC8313ECVRGDDB 数据表(PDF) 55 Page - Freescale Semiconductor, Inc

MPC8313ECVRGDDB 数据表(HTML) 55 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100

数据表下载

链接网址

MPC8313ECVRGDDB 数据表(PDF) 55 Page - Freescale Semiconductor, Inc

MPC8313ECVRGDDB 数据表(HTML) 55 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100

数据表 下载

链接网址

数据表下载