STM32F103XC datasheet(19/123 Pages) STMICROELECTRONICS

19 / 123 page

STM32F103xC, STM32F103xD, STM32F103xE

Description

Doc ID 14611 Rev 7

19/123

periodic interrupt. It is clocked by a 32.768 kHz external crystal, resonator or oscillator, the

internal low power RC oscillator or the high-speed external clock divided by 128. The

internal low-speed RC has a typical frequency of 40 kHz. The RTC can be calibrated using

an external 512 Hz output to compensate for any natural quartz deviation. The RTC features

a 32-bit programmable counter for long term measurement using the Compare register to

generate an alarm. A 20-bit prescaler is used for the time base clock and is by default

configured to generate a time base of 1 second from a clock at 32.768 kHz.

2.3.17

Timers and watchdogs

The high-density STM32F103xx performance line devices include up to two advanced-

control timers, up to four general-purpose timers, two basic timers, two watchdog timers and

a SysTick timer.

Table 4 compares the features of the advanced-control, general-purpose and basic timers.

Advanced-control timers (TIM1 and TIM8)

The two advanced-control timers (TIM1 and TIM8) can each be seen as a three-phase

PWM multiplexed on 6 channels. They have complementary PWM outputs with

programmable inserted dead-times. They can also be seen as a complete general-purpose

timer. The 4 independent channels can be used for:

●

Input capture

●

Output compare

●

PWM generation (edge or center-aligned modes)

●

One-pulse mode output

If configured as a standard 16-bit timer, it has the same features as the TIMx timer. If

configured as the 16-bit PWM generator, it has full modulation capability (0-100%).

In debug mode, the advanced-control timer counter can be frozen and the PWM outputs

disabled to turn off any power switch driven by these outputs.

Many features are shared with those of the general-purpose TIM timers which have the

same architecture. The advanced-control timer can therefore work together with the TIM

timers via the Timer Link feature for synchronization or event chaining.

Table 4.

High-density timer feature comparison

Timer

Counter

resolution

Counter

type

Prescaler

factor

DMA request

generation

Capture/compare

channels

Complementary

outputs

TIM1,

TIM8

16-bit

Up,

down,

up/down

Any integer

between 1

and 65536

Yes

TIM2,

TIM3,

TIM4,

TIM5

16-bit

Up,

down,

up/down

Any integer

between 1

and 65536

Yes

TIM6,

TIM7

16-bit

Any integer

between 1

and 65536

Yes

STM32F103xC 数据表(PDF) 19 Page - STMicroelectronics

STM32F103xC 数据表(HTML) 19 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载

链接网址

STM32F103xC 数据表(PDF) 19 Page - STMicroelectronics

STM32F103xC 数据表(HTML) 19 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表 下载

链接网址

数据表下载