AD7468BRT-R datasheet(23/28 Pages) AD

23 / 28 page

AD7466/AD7467/AD7468

Rev. C | Page 23 of 28

SCLK

SDATA

tCONVERT

tQUIET

4 LEADING ZEROS

THREE-STATE

8 BITS OF DATA

DB7

DB0

Figure 31. AD7468 Serial Interface Timing Diagram

MICROPROCESSOR INTERFACING

The serial interface on the AD7466/AD7467/AD7468 allows

the parts to be connected directly to many different micro-

processors. This section explains how to interface the AD7466/

AD7467/AD7468 with some of the more common microcontroller

and DSP serial interface protocols.

AD7466/AD7467/AD7468 to TMS320C541 Interface

The serial interface on the TMS320C541 uses a continuous

serial clock and frame synchronization signals to synchronize

the data transfer operations with peripheral devices like the

AD7466/AD7467/AD7468. The CS input allows easy inter-

facing between the TMS320C541 and the AD74xx devices,

without requiring any glue logic. The serial port of the

TMS320C541 is set up to operate in burst mode (FSM = 1

in the serial port control register, SPC) with internal CLKX

(MCM = 1 in the SPC register) and internal frame signal

(TXM = 1 in the SPC register), so both pins are configured as

outputs. For the AD7466, the word length should be set to

16 bits (FO = 0 in the SPC register). The standard synchronous

serial port interface in this DSP allows only frames with a word

length of 16 bits or 8 bits. Therefore, for the AD7467 and

AD7468 where 14 and 12 bits are required, the FO bit also

would be set up to 16 bits. In these cases, the user should keep

in mind that the last 2 bits and 4 bits for the AD7467 and

AD7468, respectively, are invalid data as the SDATA line goes

back into three-state on the 14th and 12th SCLK falling edge.

To summarize, the values in the SPC register are FO = 0,

FSM = 1, MCM = 1, and TXM = 1.

Figure 32 shows the connection diagram. For signal processing

applications, it is imperative that the frame synchronization

signal from the TMS320C541 provide equidistant sampling.

AD7466/

AD7467/

AD74681

SCLK

1ADDITIONAL PINS OMITTED FOR CLARITY.

SDATA

TMS320C5411

CLKX

CLKR

FSX

FSR

Figure 32. Interfacing to the TMS320C541

AD7466/AD7467/AD7468 to ADSP-218x Interface

The ADSP-218x family of DSPs is interfaced directly to the

AD7466/AD7467/AD7468 without any glue logic. The SPORT

control register must be set up as described in Table 9.

Table 9. SPORT Control Register Setup

Setting

Description

TFSW = RFSW = 1

Alternate framing

INVRFS = INVTFS = 1

Active low frame signal

DTYPE = 00

Right-justify data

ISCLK = 1

Internal serial clock

TFSR = RFSR = 1

Frame every word

IRFS = 0

Sets up RFS as an input

ITFS = 1

Sets up TFS as an output

SLEN = 1111

16 bits for the AD7466

SLEN = 1101

14 bits for the AD7467

SLEN = 1011

12 bits for the AD7468

AD7468BRT-R 数据表(PDF) 23 Page - Analog Devices

AD7468BRT-R 数据表(HTML) 23 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28

数据表下载