XTNETA1570MFP datasheet(36/68 Pages) TI1

36 / 68 page

TNETA1570

ATM SEGMENTATION AND REASSEMBLY DEVICE

WITH INTEGRATED 64BIT PCIHOST INTERFACE

SDNS033B − JUNE 1995 − REVISED MAY 1996

POST OFFICE BOX 655303

• DALLAS, TEXAS 75265

POST OFFICE BOX 1443

• HOUSTON, TEXAS 77251−1443

PRINCIPLES OF OPERATION

enable (bit 31)

This bit is set by the host indicating that packets can be received on this VPI channel. When this bit is cleared,

packets received on this VPI channel are dropped.

base pointer (bits 30 −16)

This field is initialized by the host indicating the base address of the area in the RX DMA state table in control

memory assigned to this VPI channel. The value in this field is used together with the valid VCI range (next entry

in this register) to form the address in the RX DMA state table. Valid values are 800 −7FFF(h).

valid VCI range (bits 15 −0)

This field contains the upper value of the range of the VCI channels that can be received on this VPI channel.

The lower value of the range is always zero. The VCI value of the incoming cell is compared with this field. If

this value is less then or equal to the valid VCI range, the cells for this VCI are accepted. The VCI is masked

before it is compared. Valid values are 0 − F00(h).

The address to the RX DMA state table is calculated as follows:

[[(base pointer + VCI value of incoming cell + value at base register 0)

× 8] × 4] (i.e., shift left five times).

This value never exceeds the value of the maximum address in the control-memory map.

VCIs causing values greater than the value of the maximum address in the control-memory map can be

transferred to the data buffers if a VCI mask is used, which reduces the value used by the reassembly engine

to a value less than the maximum control-memory address.

receive DMA state table

Addressing

Control-memory address 04000 − 3FFFF. The VCI value of the incoming ATM cell

combined with the value of the entry in the RX VPI/VCI pointer table is used to form

the address.

Size

Max logical entries: 30720

Max 32-bit words: 245760

Min logical entries: 1

Min 32-bit words: 8

The receive DMA state table resides in control memory and contains 30720 entries, allowing for the

simultaneous reassembly of 30720 packets. Each state entry contains eight 32-bit words. The receive DMA

state table has several entries that must be initialized, including whether that particular state is on or off, etc.

The entries in the receive DMA state table are shown below.

ENTRY

DESCRIPTION

Word 0

Control field, EFCN cell counter, packet length

Word 1

Current buffer address

Word 2

Start-of-buffer address

Word 3

Current transparent-AAL packet counter, current buffer length

Word 4

Start-of-packet pointer

Word 5

Partial AAL5 receive CRC

Word 6

On filter bit, FIFO/RX free-buffer ring-pointer table entry

Word 7

Time-out value, current time-out count

XTNETA1570MFP 数据表(PDF) 36 Page - Texas Instruments

XTNETA1570MFP 数据表(HTML) 36 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68

数据表下载