STW82102B datasheet(35/67 Pages) STMICROELECTRONICS

35 / 67 page

STW82102B

I2C bus interface

Doc ID 018516 Rev 2

35/67

9.1.4

Device addressing

To start the communication between the Master and the STW82102B, the master must

initiate with a START condition. Following this, the master sends onto the SDA line 8 bits

(MSB first) corresponding to the device select address and read or write mode.

The first 7 MSBs are the device address identifier, corresponding to the I2C-Bus definition.

For the STW82102B the address is set as ’1101A2A1A0’, 3-bits programmable. The 8th bit

(LSB) is the read or write operation bit (the RW bit is set to 1 in read mode and to 0 in write

mode).

After a START condition the STW82102B identifies the device address on the bus and, if

matched, it acknowledge the identification on SDA bus during the 9th clock pulse.

9.1.5

Single-byte write mode

Following a START condition the master sends a device select code with the RW bit set to 0.

The STW82102B gives an acknowledge and waits for the internal sub-address (1 byte). This

byte provides access to any of the internal registers.

After reception of the internal byte sub-address the STW82102B again responds with an

acknowledge. A single-byte write to sub-address 0x00 would affect DATA_OUT[47:40], a

single-byte write with sub-address 0x04 would affect DATA_OUT[15:8] and so on.

9.1.6

Multi-byte write mode

The multi-byte write mode can start from any internal address. The master sends the data

bytes and each one is acknowledged. The master terminates the transfer by generating a

STOP condition.

The sub-address determines the starting byte. For example, a multi-byte write with sub-

address 0x01 and 4 DATA_IN bytes affects 4 bytes starting at address 0x01 (registers at

addresses 0x01, 0x02, 0x03 and 0x04 are modified).

9.1.7

Current byte address read

In the current byte address read mode, following a START condition, the master sends the

device address with the RW bit set to 1 (No sub-address is needed as there is only 1 byte

read register). The STW82102B acknowledges this and outputs the data byte. The master

does not acknowledge the received byte, but terminates the transfer with a STOP condition.

1101A2A1A0

0ack

sub-address

byte

ack

DATA IN

ack

1101A2A1A0

0ack

sub-address

byte

ack

DATA IN

ack

DATA

ack

1101A2A1A0

ack

DATA OUT

No ack

STW82102B 数据表(PDF) 35 Page - STMicroelectronics

STW82102B 数据表(HTML) 35 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67

数据表下载

链接网址

STW82102B 数据表(PDF) 35 Page - STMicroelectronics

STW82102B 数据表(HTML) 35 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67

数据表 下载

链接网址

数据表下载