| 数据搜索系统,热门电子元器件搜索 |
|
WI.232FHSS-25-R 数据表(PDF) 40 Page - Radiometrix Ltd |
|
|
|||||||||||||||||||||||||||||
WI.232FHSS-25-R 数据表(HTML) 40 Page - Radiometrix Ltd |
|
40 / 67 page ![]() WI.232FHSS-25-R/ WI.232FHSS-250-R DATASHEET 39 Revision 1.1.0 4.1.10. Verbose Mode (regSHOWVER) regNVSHOWVER (0x0A) regSHOWVER (0x55) R/W R/W R/W R/W R/W R/W R/W R/W B7 B6 B5 B4 B3 B2 B1 B0 7 6 5 4 3 2 1 0 Default Verbose Mode: Enabled (0x01) Setting this register to 0x00 will suppress the start-up message, including firmware version, which is sent to the UART when the module is reset. A value of 0x01 will cause the message to be displayed after reset. By default, the module start-up message will be displayed. The non-volatile counterpart, regSHOWVER, has no function. Verbose Mode Meaning 0x00 Startup message will NOT be displayed upon reset or power-up 0x01 Startup message will be displayed upon reset or power-up. This is a blocking call, and any incoming UART data will be lost during the transmission of this message through the TxD pin. All UART commands must be sent after this message has completed. 0x02 Startup message will be displayed upon reset or power-up. This is a non-blocking call. Any incoming UART data will be buffered, and incoming UART commands will be processed. If a change of baud rate is commanded while the startup message is being output, the current byte will finish at the current baud rate, and subsequent bytes will be transmitted at the new baud rate. * Available in 250-R firmware 1.1.0 and newer only. Table 16, Verbose Mode Settings 4.1.11. CSMA Enable (regCSMAMODE) regNVCSMAMODE (0x0B) regCSMAMODE (0x56) R/W R/W R/W R/W R/W R/W R/W R/W B7 B6 B5 B4 B3 B2 B1 B0 7 6 5 4 3 2 1 0 Default CSMA Enable: Enabled (0x01) Carrier-sense multiple access (CSMA) is a best-effort delivery system that listens to the channel before transmitting a message. If another Wi.232 module is already transmitting when a message is queued, the module will wait before sending its payload. This helps to eliminate RF message corruption at the expense of additional latency. Setting this register to 0x01 will enable CSMA. Setting this register to 0x00 will disable CSMA. By default, CSMA is enabled. |
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |