ADP7182ACPZ-R7 datasheet(21/28 Pages) ANACHIP

21 / 28 page

Data Sheet

ADP7182

Rev. A | Page 21 of 28

APPLICATIONS INFORMATION

ADIsimPower DESIGN TOOL

The ADP7182 is supported by the ADIsimPower™ design tool

set. ADIsimPower is a collection of tools that produce complete

power designs optimized for a specific design goal. The tools

enable the user to generate a full schematic, bill of materials,

and calculate performance in minutes. ADIsimPower can

optimize designs for cost, area, efficiency, and parts count

taking into consideration the operating conditions and

limitations of the IC and all real external components. For

more information about, and to obtain ADIsimPower

design tools, visit www.analog.com/ADIsimPower.

CAPACITOR SELECTION

Output Capacitor

The ADP7182 is designed for operation with small space-saving

ceramic capacitors; however, it functions with most commonly

used capacitors as long as care is taken with regard to the ESR

value. The ESR of the output capacitor affects the stability of the

LDO control loop. A minimum of 2.2 µF capacitance with an

ESR of 0.2 Ω or less is recommended to ensure the stability of

the ADP7182. Transient response to changes in load current is

also affected by output capacitance. Using a larger value of output

capacitance improves the transient response of the ADP7182

to large changes in load current. Figure 78 shows the transient

responses for an output capacitance value of 2.2 µF.

CH1 100mA BW

CH2 50mV

W M40µs A CH1

–122mA

T 10.60%

VOUT

LOAD CURRENT

Figure 78. Output Transient Response, COUT = 2.2 µF

Input Bypass Capacitor

Connecting a 2.2 µF capacitor from VIN to GND reduces the

circuit sensitivity to PCB layout, especially when long input

traces or high source impedance are encountered. When more

than 2.2 µF of output capacitance is required, increase the input

capacitance to match it.

Input and Output Capacitor Properties

As long as they meet the minimum capacitance and maximum

ESR requirements, any good quality ceramic capacitors can be

used with the ADP7182. Ceramic capacitors are manufactured

with a variety of dielectrics, each with different behavior over

temperature and applied voltage. Capacitors must have a dielectric

adequate to ensure the minimum capacitance over the necessary

temperature range and dc bias conditions. X5R or X7R dielectrics

with a voltage rating of 25 V or 50 V are recommended. Due to

their poor temperature and dc bias characteristics, Y5V and Z5U

dielectrics are not recommended.

Figure 79 depicts the capacitance vs. voltage bias characteristics

of an 0805, 2.2 µF, 25 V, X5R capacitor. The voltage stability of a

capacitor is strongly influenced by the capacitor size and voltage

rating. In general, a capacitor in a larger package or higher voltage

rating exhibits better stability. The temperature variation of the

X5R dielectric is ~ ±15% over the −40°C to +85°C temperature

range and is not a function of package or voltage rating.

2.5

0.5

1.0

1.5

2.0

DC BIAS (V)

Figure 79. Capacitance vs. DC Bias Characteristics

Use Equation 1 to determine the worst-case capacitance accounting

for capacitor variation over temperature, component tolerance,

and voltage.

CEFF = CBIAS × (1 − TEMPCO) × (1 − TOL)

(1)

where:

CBIAS is the effective capacitance at the operating voltage, which

is −3 V for this example.

TEMPCO is the worst-case capacitor temperature coefficient.

TOL is the worst-case component tolerance.

In this example, the worst-case temperature coefficient (TEMPCO)

over −40°C to +85°C is 15% for an X5R dielectric. The tolerance

of the capacitor (TOL) is 10%, and the CBIAS is 2.08 µF at a 3 V bias,

as shown in Figure 79.

Substituting these values in Equation 1 yields

CEFF = 2.08 μF × (1 − 0.15) × (1 − 0.1) = 1.59 µF

Therefore, the capacitor chosen in this example meets the

minimum capacitance requirement of the LDO over temperature

and tolerance at the chosen output voltage of −3 V.

To guarantee the performance of the ADP7182, it is imperative

that the effects of dc bias, temperature, and tolerances on the

behavior of the capacitors be evaluated for each application.

ADP7182ACPZ-R7 数据表(PDF) 21 Page - Anachip Corp

ADP7182ACPZ-R7 数据表(HTML) 21 Page - Anachip Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28

数据表下载