ADE7753ARSRL datasheet(20/60 Pages) AD

20 / 60 page

ADE7753

Rev. C | Page 20 of 60

SAGCYC [7:0] = 0x04

3 LINE CYCLES

SAG RESET HIGH

WHEN CHANNEL 2

EXCEEDS SAGLVL [7:0]

FULL SCALE

SAGLVL [7:0]

SAG

CHANNEL 2

02875-0-043

Figure 43. ADE7753 Sag Detection

Figure 43 shows the line voltage falling below a threshold that is

set in the sag level register (SAGLVL[7:0]) for three line cycles.

The quantities 0 and 1 are not valid for the SAGCYC register,

and the contents represent one more than the desired number

of full line cycles. For example, when the sag cycle (SAGCYC[7:0])

contains 0x04, the SAG pin goes active low at the end of the

third line cycle for which the line voltage (Channel 2 signal)

falls below the threshold, if the DISSAG bit in the mode register

is Logic 0. As is the case when zero crossings are no longer

detected, the sag event is also recorded by setting the SAG flag

in the interrupt status register. If the SAG enable bit is set to

Logic 1, the IRQ logic output goes active low—see the

section. The

ADE7753

Interrupts

SAG pin goes logic high again when the

absolute value of the signal on Channel 2 exceeds the sag level

set in the sag level register. This is shown in

when the

Figure 43

SAG pin goes high again during the fifth line cycle from the

time when the signal on Channel 2 first dropped below the

threshold level.

Sag Level Set

The contents of the sag level register (1 byte) are compared to

the absolute value of the most significant byte output from LPF1

after it is shifted left by one bit, thus, for example, the nominal

maximum code from LPF1 with a full-scale signal on Channel 2

is 0x2518—see the Channel 2 Sampling section. Shifting one bit

left gives 0x4A30. Therefore writing 0x4A to the SAG level

0x01 puts the sag detection level at 0. The SAG level register is

compared to the most significant byte of a waveform sample

after the shift left and detection is made when the contents of

the sag level register are greater.

PEAK DETECTION

The ADE7753 can also be programmed to detect when the

absolute value of the voltage or current channel exceeds a

specified peak value. Figure 44 illustrates the behavior of the

peak detection for the voltage channel. Both Channel 1 and

Channel 2 are monitored at the same time.

PKV RESET LOW

WHEN RSTSTATUS

VPKLVL[7:0]

READ RSTSTATUS

PKV INTERRUPT

FLAG (BIT 8 OF

STATUS REGISTER)

02875-0-088

Figure 44. ADE7753 Peak Level Detection

Figure 44 shows a line voltage exceeding a threshold that is set

in the voltage peak register (VPKLVL[7:0]). The voltage peak

event is recorded by setting the PKV flag in the interrupt status

mask register, the IRQ logic output goes active low. Similarly,

the current peak event is recorded by setting the PKI flag in the

interrupt status register—see the

section.

ADE7753 Interrupts

Peak Level Set

The contents of the VPKLVL and IPKLVL registers are

respectively compared to the absolute value of Channel 1 and

Channel 2 after they are multiplied by 2. Thus, for example, the

nominal maximum code from the Channel 1 ADC with a full-

scale signal is 0x2851EC—see the Channel 1 Sampling section.

Multiplying by 2 gives 0x50A3D8. Therefore, writing 0x50 to

the IPKLVL register, for example, puts the Channel 1 peak

detection level at full scale and sets the current peak detection

to its least sensitive value. Writing 0x00 puts the Channel 1

detection level at 0. The detection is done by comparing the

contents of the IPKLVL register to the incoming Channel 1

sample. The IRQ pin indicates that the peak level is exceeded if

the PKI or PKV bits are set in the interrupt enable register

(IRQEN[15:0]) at Address 0x0A.

Peak Level Record

The ADE7753 records the maximum absolute value reached by

Channel 1 and Channel 2 in two different registers—IPEAK

and VPEAK, respectively. VPEAK and IPEAK are 24-bit

unsigned registers. These registers are updated each time the

absolute value of the waveform sample from the corresponding

channel is above the value stored in the VPEAK or IPEAK

the maximum absolute value observed on the Channel 2 input.

The contents of IPEAK represent the maximum absolute value

observed on the Channel 1 input. Reading the RSTVPEAK and

RSTIPEAK registers clears their respective contents after the read

operation.

ADE7753ARSRL 数据表(PDF) 20 Page - Analog Devices

ADE7753ARSRL 数据表(HTML) 20 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

数据表下载