AD7980BCPZ-R2 datasheet(8/28 Pages) AD

8 / 28 page

AD7980

Data Sheet

Rev. C | Page 8 of 28

TERMINOLOGY

Integral Nonlinearity Error (INL)

INL refers to the deviation of each individual code from a line

drawn from negative full scale through positive full scale. The

point used as negative full scale occurs ½ LSB before the first

code transition. Positive full scale is defined as a level 1½ LSB

beyond the last code transition. The deviation is measured from

the middle of each code to the true straight line (see Figure 26).

Differential Nonlinearity Error (DNL)

In an ideal ADC, code transitions are 1 LSB apart. DNL is the

maximum deviation from this ideal value. It is often specified in

terms of resolution for which no missing codes are guaranteed.

Offset Error

The first transition should occur at a level ½ LSB above analog

ground (38.1 µV for the 0 V to 5 V range). The offset error is

the deviation of the actual transition from that point.

Gain Error

The last transition (from 111 … 10 to 111 … 11) should

occur for an analog voltage 1½ LSB below the nominal full

scale (4.999886 V for the 0 V to 5 V range). The gain error is

the deviation of the actual level of the last transition from the

ideal level after the offset is adjusted out.

Spurious-Free Dynamic Range (SFDR)

SFDR is the difference, in decibels (dB), between the rms

amplitude of the input signal and the peak spurious signal.

Effective Number of Bits (ENOB)

ENOB is a measurement of the resolution with a sine wave

input. It is related to SINAD by the following formula

ENOB = (SINADdB − 1.76)/6.02

and is expressed in bits.

Noise-Free Code Resolution

Noise-free code resolution is the number of bits beyond which

it is impossible to distinctly resolve individual codes. It is

calculated as

Noise-Free Code Resolution = log2(2N/Peak-to-Peak Noise)

and is expressed in bits.

Effective Resolution

Effective resolution is calculated as

Effective Resolution = log2(2N/RMS Input Noise)

and is expressed in bits.

Total Harmonic Distortion (THD)

THD is the ratio of the rms sum of the first five harmonic

components to the rms value of a full-scale input signal and is

expressed in dB.

Dynamic Range

Dynamic range is the ratio of the rms value of the full scale to

the total rms noise measured with the inputs shorted together.

The value for dynamic range is expressed in dB. It is measured

with a signal at −60 dBFS to include all noise sources and DNL

artifacts.

Signal-to-Noise Ratio (SNR)

SNR is the ratio of the rms value of the actual input signal to the

rms sum of all other spectral components below the Nyquist

frequency, excluding harmonics and dc. The value for SNR is

expressed in dB.

Signal-to-(Noise + Distortion) Ratio (SINAD)

SINAD is the ratio of the rms value of the actual input signal to

the rms sum of all other spectral components below the Nyquist

frequency, including harmonics but excluding dc. The value for

SINAD is expressed in dB.

Aperture Delay

Aperture delay is the measure of the acquisition performance. It

is the time between the rising edge of the CNV input and when

the input signal is held for a conversion.

Transient Response

Transient response is the time required for the ADC to

accurately acquire its input after a full-scale step function is

applied.

AD7980BCPZ-R2 数据表(PDF) 8 Page - Analog Devices

AD7980BCPZ-R2 数据表(HTML) 8 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28

数据表下载

链接网址

AD7980BCPZ-R2 数据表(PDF) 8 Page - Analog Devices

AD7980BCPZ-R2 数据表(HTML) 8 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28

数据表 下载

链接网址

数据表下载