SLAS191A datasheet(30/86 Pages) TI

30 / 86 page

1–24

$ML1

BIT.B

#01h,P0IN

; Test P0.0

JNZ

$ML1

; Do nothing if P0.0 low

1.2.13

How to Use an Interrupt Routine

Assemble and download the file gs_stk4.asm in the examples directory, as described previously.

When an interrupt occurs, the program sends the contents of the program counter and status

Next, the program branches to the starting address of the interrupt routine.

The interrupt routine normally ends with the RETI instruction.

The RETI instruction loads the data, which was saved to the stack at the beginning of the interrupt

routine, to the status register and program counter.

The program continues from the point of interruption.

Using interrupt routines allows the MSP430 to use low power modes. Selecting a low power mode causes

the program to stop at the current position, and an activity that causes an interrupt automatically clears the

low power mode. The interrupt continues program execution at the starting address of the corresponding

interrupt routine. The RETI loads the saved program data to the status register and program counter.

Loading the status register and program counter clears out the low power mode bits, and the program

continues with the next instruction. Figure 1–20 is the Basic Timer Interrupt routine.

BIS

#CPUOFF,SR

; set CPUoff Bit

;****************************************************************************

; Basic Timer Interrupt routine

;****************************************************************************

Int_BT

; Basic Timer 128 Hz (7.8 ms)

DEC.B

lcd_timer

; decrement SW lcd-timer

JNZ

Int_BT_end

; !0 : no action

BIC

#CPUOFF,0(SP)

; Clear CPUoff Bit

MOV.B

#lcd+ival,lcd_timer

; = 0 : load again

Int_BT_end

RETI

To use the interrupts, the interrupt vector table must be set up as follows:

;****************************************************************************

; Interrupt vectors

;****************************************************************************

.sect ”int_Vect”, USER_END-31

.word

RESET

; no source

.word

Int_BT

; Basic Timer

.word

RESET

; no source

.word

RESET

; no source

.word

RESET

; no source

.word

RESET

; no source

.word

RESET

; no source

.word

RESET

; no source

.word

RESET

; no source

.word

RESET

; no source

.word

RESET

; no source

.word

RESET

; no source

.word

RESET

; no source

.word

RESET

; no source

.word

RESET

; NMI, Osc. fault

.word

RESET

; POR, ext. Reset, Watchdog

.end

Figure 1–20. Basic Timer Interrupt Routine

SLAS191A 数据表(PDF) 30 Page - Texas Instruments

SLAS191A 数据表(HTML) 30 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86

数据表下载

链接网址

SLAS191A 数据表(PDF) 30 Page - Texas Instruments

SLAS191A 数据表(HTML) 30 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86

数据表 下载

链接网址

数据表下载