| 数据搜索系统,热门电子元器件搜索 |
|
CC2500-RTY1 数据表(PDF) 70 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
CC2500-RTY1 数据表(HTML) 70 Page - Texas Instruments |
|
70 / 99 page ![]() CC2500 SWRS040C Page 70 of 89 0x16: MCSM2 – Main Radio Control State Machine Configuration Bit Field Name Reset R/W Description 7:5 Reserved R0 Reserved 4 RX_TIME_RSSI 0 R/W Direct RX termination based on RSSI measurement (carrier sense). 3 RX_TIME_QUAL 0 R/W When the RX_TIME timer expires the chip stays in RX mode if sync word is found when RX_TIME_QUAL=0, or either sync word is found or PQT is set when RX_TIME_QUAL=1. 2:0 RX_TIME[2:0] 7 (111) R/W Timeout for sync word search in RX for both WOR mode and normal RX operation. The timeout is relative to the programmed EVENT0 timeout. The RX timeout in µs is given by EVENT0·C(RX_TIME, WOR_RES) ·26/X, where C is given by the table below and X is the crystal oscillator frequency in MHz: RX_TIME[2:0] WOR_RES = 0 WOR_RES = 1 WOR_RES = 2 WOR_RES = 3 0 (000) 3.6058 18.0288 32.4519 46.8750 1 (001) 1.8029 9.0144 16.2260 23.4375 2 (010) 0.9014 4.5072 8.1130 11.7188 3 (011) 0.4507 2.2536 4.0565 5.8594 4 (100) 0.2254 1.1268 2.0282 2.9297 5 (101) 0.1127 0.5634 1.0141 1.4648 6 (110) 0.0563 0.2817 0.5071 0.7324 7 (111) Until end of packet As an example, EVENT0=34666, WOR_RES=0 and RX_TIME=6 corresponds to 1.95 ms RX timeout, 1 s polling interval and 0.195% duty cycle. Note that WOR_RES should be 0 or 1 when using WOR because using WOR_RES > 1 will give a very low duty cycle. In applications where WOR is not used all settings of WOR_RES can be used. The duty cycle using WOR is approximated by: RX_TIME[2:0] WOR_RES = 0 WOR_RES = 1 0 (000) 12.50% 1.95% 1 (001) 6.250% 9765 ppm 2 (010) 3.125% 4883 ppm 3 (011) 1.563% 2441 ppm 4 (100) 0.781% NA 5 (101) 0.391% NA 6 (110) 0.195% NA 7 (111) NA Note that the RC oscillator must be enabled in order to use setting 0-6, because the timeout counts RC oscillator periods. WOR mode does not need to be enabled. The timeout counter resolution is limited: With RX_TIME=0, the timeout count is given by the 13 MSBs of EVENT0, decreasing to the 7 MSBs of EVENT0 with RX_TIME=6. |
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |