AD9953_15 datasheet(27/32 Pages) AD

27 / 32 page

AD9953

Rev. A | Page 27 of 32

INSTRUCTION BYTE

The instruction byte contains the following information:

Table 9.

MSB

LSB

R/W

R/W—Bit 7 of the instruction byte determines whether a read

etermine which register is accessed during the data transfer

portion of the communications cycle.

SERIAL INTERFACE PORT PIN DESCRIPTION

SCLK—Serial Clock. The serial clock pin is used to synchronize

data to and from the AD9953 and to run the internal state

machines. SCLK maximum frequency is 25 MHz.

CSB—Chip Select Bar. CSB is active low input t

an one device on the same serial communications line. The

SDO and SDIO pins will go to a high impedance state when this

input is high. If driven high during any communications cycle,

that cycle is suspended until CS

or write data transfer will occur after the instruction byte write.

Logic High indicates read operation. Logic 0 indicates a write

operation.

X, X—Bits 6 and 5 of the instruction byte are Don’t Care.

A4, A3, A2, A1, A0—Bits 4, 3, 2, 1, 0 of the instruction byte

hat allows more

is reactivated low. Chip select

can be tied low in systems that maintain control of SCLK.

SDIO—Serial Data I/O. Data is always written into the AD9953

on this pin. However, this pin can be used as a bidirectional

data line. Bit 9 of Register Address 0x00 controls the

configuration of this pin. The default is Logi

nfigures the SDIO pin as bidirectional.

SDO—Serial Data Out. Data is read from this pin for protocols

that use separate lines for transmitting and receiving data. In the

case where the AD9953 operates in a single bidirectional I/O mode,

this pin does not output data and is set to a high impedance state.

IOSYNC—It synchronizes the I/O port state machines without

affecting the addressable register’s contents. An

put on the IOSYNC pin causes the current communication

ycle to abort. After IOSYNC returns low (Logic 0), another

communication cycle may begin, starting with the instruction

byte write.

MSB/LSB TRANSFERS

The AD9953 serial port can support both most significant bit

(MSB) first or least significant bit (LSB) firs

unctionality is controlled by the Control Register 0x00 <8> bit.

he default value of Control Register 0x00 <8> is low (MSB

rst). When Control Register 0x00 <8> is set high, the AD9953

rial port is in LSB first format. The instruction byte must be

ddress first

I/O operation is complete. All data written to (read from) the

AD9953 must be (will be) in MSB first order. If the LSB mode is

active, the serial port controller will generate the least signifi-

cant byte address first followed by the next greater significant byte

addresses until the I/O operation is complete. All data written to

(read from) the AD9953 must be (will be) in LSB first order.

Example Operation

tude scale factor register in MSB first format,

apply an instruction byte of 0x02 [serial address is 00010(b)].

From this instruction, the internal controller will know to use

the first byte as the most significant byte. The first two bits will

be recorded as the auto ramp rate speed control bits, and the

next six bits will be the most significant bits of the amplitude

scale factor. The second byte will be applied as the eight less

significant bits of the amplitude scale factor ASF<7:0>.

To write the amplitude scale factor regis

SB first format,

l register has already been set for LSB first

format, apply an instruction byte of 0x40. From this instruction,

the internal controller will know to use the first byte as the least

significant byte of the amplitude scale factor ASF<0:7>. The

second byte will be split into the first six bits ASF<8:13> and the

last two will provide the auto ramp rate speed control bits

ARRSC<0:1>.

D9953

The AD9953 supports an externally controlled or hardware

power-down feature as well as the more common software

programmable power-down bits found in previous ADI DDS

products.

The software control power-down allows the DAC, PLL, input

clock circuitry, and digital logic to be individually powered

down via unique control bits (CFR1<7:4>). With the exception

ts are not active when the externally

controlled power-down pin (PWRDWNCTL) is high. External

power-down control is supported on the AD9953 via the

PWRDWNCTL input pin. When the PWRDWNCTL input pin

is high, the AD9953 will enter a power-down mode based on

the CFR1<3> bit. When the PWRDWNCTL input pin is low,

the external power-down control is inactive.

c 0, which

assuming the contro

active high

Power-Down Functions of the A

t data formats. This

of CFR1<6>, these bi

written in the format indicated by Control Register 0x00 <8>. If

the AD9953 is in LSB first mode, the instruction byte must be

written from least significant bit to most significant bit.

For MSB first operation, the serial port controller will generate

the most significant byte (of the specified register) a

followed by the next lesser significant byte addresses until the

To write the ampli

ter in L

AD9953 数据表(PDF) 27 Page - Analog Devices

AD9953 数据表(HTML) 27 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

数据表下载