LCL8052ACPD datasheet(5/21 Pages) INTERSIL

5 / 21 page

5-10

Absolute Maximum Ratings

Thermal Information

ICL8052, ICL8068

Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

±18V

Differential Input Voltage

(8068) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

±30V

(8052) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

±6V

Input Voltage (Note 2). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

±15V

Output Short Circuit Duration All Outputs (Note 3). . . . . . . Indeﬁnite

ICL7104

V+ Supply (GND to V+) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12V

V++ to V-. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32V

Positive Supply Voltage (GND to V++) . . . . . . . . . . . . . . . . . . . . 17V

Negative Supply Voltage (GND to V-). . . . . . . . . . . . . . . . . . . . .-17V

Analog Input Voltage (Pins 32 - 39)(Note 4). . . . . . . . . . . . V++ to V-

Digital Input Voltage

(Pins 2 - 30) (Note 5) . . . . . . . . . . . . (GND - 0.3V) to (V+ + 0.3V)

Operating Conditions

Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . .0oC to 70oC

Thermal Resistance (Typical, Note 1)

θJA (oC/W) θJC (oC/W)

14 Ld PDIP Package . . . . . . . . . . . . . .

100

N/A

40 Ld PDIP Package . . . . . . . . . . . . . .

N/A

14 Ld CERDIP Package . . . . . . . . . . .

Maximum Junction Temperature (Ceramic Package) . . . . . . . . . 175oC

Maximum Junction Temperature (Plastic Package) . . . . . . . . 150oC

Maximum Storage Temperature Range . . . . . . . . . .-65oC to 150oC

Maximum Lead Temperature (Soldering, 10s) . . . . . . . . . . . . 300oC

CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation

of the device at these or any other conditions above those indicated in the operational sections of this speciﬁcation is not implied.

NOTES:

θJA is measured with the component mounted on an evaluation PC board in free air.

2. For supply voltages less than

±15V, the absolute maximum input voltage is equal to the supply voltage.

3. Short circuit may be to ground or either supply. Rating applies to 70oC ambient temperature.

4. Input voltages may exceed the supply voltages provided the input current is limited to

±100µA.

5. Connecting any digital inputs or outputs to voltages greater than V+ or less than GND may cause destructive device latchup. For this

reason it is recommended that the power supply to the ICL7104 be established before any inputs from sources not on that supply are

applied.

ICL7104 Electrical Speciﬁcations V+ = +5V, V++ = +15V, V- = -15V, TA = 25oC, fCLOCK = 200kHz

PARAMETER

SYMBOL

TEST

CONDITIONS

MIN

TYP

MAX

UNITS

Clock Input, CLK 1

IIN

VIN = +5V to 0V

±2

±7

±30

µA

Comparator I/P, COMP IN (Note 6)

IIN

VIN = 0V to +5V

-10

±0.001

µA

Inputs with Pulldown, MODE

IIH

VIN = +5V

µA

IIL

VIN = 0V

-10

±0.01

µA

Inputs with Pullups

SEN, R/H

LBEN, MBEN, HBEN, CE/LD (Note 7)

IIH

VIN = +5V

-10

±0.01

µA

IIL

VIN = 0V

-30

-5

-1

µA

Input High Voltage, All Digital Inputs

VIH

2.5

2.0

Input Low Voltage, All Digital Inputs

VIL

1.5

1.0

Digital Outputs Three-Stated On,

LBEN, MBEN (16 Only), HBEN, CE/LD

BIT n, POL, OR (Note 8)

VOL

IOL = 1.6mA

0.27

0.4

VOH

IOH = -10µA

4.5

VOH

IOH = -240µA

2.4

3.5

Digital Outputs Three-Stated Off

Bit n, POL, OR

IOL

≤ VOUT ≤ V+

-10

±0.001

+10

µA

Non Three-State Digital Output

STTS

VOL

IOL = 3.2mA

0.3

0.4

VOH

IOH = -400µA

2.4

3.3

Clock 2

VOL

IOL= 320µA

0.5

VOH

IOH = -320µA

4.5

Clock 3 (-14 Only)

VOL

IOL = 1.6mA

0.27

0.4

VOH

IOH = -320µA

2.4

3.5

ICL8052/ICL7104, ICL8068/ICL7104

LCL8052ACPD 数据表(PDF) 5 Page - Intersil Corporation

LCL8052ACPD 数据表(HTML) 5 Page - Intersil Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

数据表下载