93LC66A/B

© 1997 Microchip Technology Inc.

Preliminary

DS21209A-page 3

2.0

PIN DESCRIPTION

2.1

Chip Select (CS)

A high level selects the device; a low level deselects the

device and forces it into standby mode. However, a pro-

gramming cycle which is already in progress will be

completed, regardless of the Chip Select (CS) input

signal. If CS is brought low during a program cycle, the

device will go into standby mode as soon as the pro-

gramming cycle is completed.

consecutive instructions. If CS is low, the internal con-

trol logic is held in a RESET status.

2.2

Serial Clock (CLK)

The Serial Clock (CLK) is used to synchronize the com-

munication between a master device and the 93LC66A/

B. Opcode, address, and data bits are clocked in on the

positive edge of CLK. Data bits are also clocked out on

the positive edge of CLK.

CLK can be stopped anywhere in the transmission

sequence (at high or low level) and can be continued

freedom in preparing opcode, address, and data.

CLK is a “Don't Care” if CS is low (device deselected).

If CS is high, but a START condition has not been

detected, any number of clock cycles can be received

by the device without changing its status (i.e., waiting

for a START condition).

CLK cycles are not required during the self-timed

WRITE (i.e., auto ERASE/WRITE) cycle.

After detection of a START condition the specified num-

ber of clock cycles (respectively low to high transitions

of CLK) must be provided. These clock cycles are

required to clock in all required opcode, address, and

data bits before an instruction is executed (Table 2-1

and Table 2-2). CLK and DI then become don't care

inputs waiting for a new START condition to be

detected.

2.3

Data In (DI)

Data In (DI) is used to clock in a START bit, opcode,

address, and data synchronously with the CLK input.

2.4

Data Out (DO)

Data Out (DO) is used in the READ mode to output data

tive edge of CLK).

This pin also provides READY/BUSY status information

during ERASE and WRITE cycles. READY/BUSY sta-

tus information is available on the DO pin if CS is

brought high after being low for minimum chip select

been initiated.

The status signal is not available on DO, if CS is held

low during the entire ERASE or WRITE cycle. In this

case, DO is in the HIGH-Z mode. If status is checked

after the ERASE/WRITE cycle, the data line will be high

to indicate the device is ready.

TABLE 2-1

INSTRUCTION SET FOR 93LC66A

Instruction

SB

Opcode

Address

Data In

Data Out

Req. CLK Cycles

ERASE

1

11

A8

A7

A6

A5

A4

A3

A2

A1

A0

—

(RDY/BSY)

12

ERAL

1

00

1

0

X

X

X

X

X

X

X

—

(RDY/BSY)

12

EWDS

1

00

0

0

X

X

X

X

X

X

X

—

HIGH-Z

12

EWEN

1

00

1

1

X

X

X

X

X

X

X

—

HIGH-Z

12

READ

1

10

A8

A7

A6

A5

A4

A3

A2

A1

A0

—

D7 - D0

20

WRITE

1

01

A8

A7

A6

A5

A4

A3

A2

A1

A0

D7 - D0

(RDY/BSY)

20

WRAL

1

00

0

1

X

X

X

X

X

X

X

D7 - D0

(RDY/BSY)

20

TABLE 2-2

INSTRUCTION SET FOR 93LC66B

Instruction

SB

Opcode

Address

Data In

Data Out

Req. CLK Cycles

ERASE

1

11

A7

A6

A5

A4

A3

A2

A1

A0

—

(RDY/BSY)

11

ERAL

1

00

1

0

X

X

X

X

X

X

—

(RDY/BSY)

11

EWDS

1

00

0

0

X

X

X

X

X

X

—

HIGH-Z

11

EWEN

1

00

1

1

X

X

X

X

X

X

—

HIGH-Z

11

READ

1

10

A7

A6

A5

A4

A3

A2

A1

A0

—

D15 - D0

27

WRITE

1

01

A7

A6

A5

A4

A3

A2

A1

A0

D15 - D0

(RDY/BSY)

27

WRAL

1

00

0

1

X

X

X

X

X

X

D15 - D0

(RDY/BSY)

27