E5CZ-R2ML datasheet(28/64 Pages) OMRON

28 / 64 page

Parameters

a-m

m-sp

sp-m

ct1

0.0

lcr1

0.0

r-s

run

al-1

al1h

al1l

al-2

al2h

al2l

al-3

al3h

al3l

0.0

c-o

0.0

cmwt

off

ct1

0.0

off

lcr1

0.0

hb1

0.0

hs1

50.0

sp-0

sp-1

sp-2

sp-3

ins

0.0

insh

0.0

8.0

233

c-sc

1.00

c-db

0.0

of-r

50.0

hys

1.0

chys

1.0

sprt

off

ol-h

105.0

ol-l

-5.0

psel

cwf

u-no

bps

9.6

len

sbit

prty

even

sdwt

oapt

icpt

wtpt

off

insl

0.0

Power ON

Starting in manual mode.

Manual control level

PID control

only

PV/MV

Press the

O Key for

at least 1 s

Press the

O Key for at

least 3 s. Displays other than

that for switching between

automatic and manual.

Adjustment Level

Press the

O Key less than 1 s.

Press the

O Key less than 1 s.

Operation Level

AT execute/cancel

Communications writing

Heater current 1 value

monitor

Leakage current 1

monitor

HS alarm 1

Heater burnout detection 1

SP 0

SP 3

SP 2

SP1

SP used by

multi-SP

Temperature input shift

1-point shift

Set either of these parameters.

Upper-limit temperature

input shift value

2-point shift

Lower-limit temperature

input shift value

Proportional band

Integral time

PID settings

Derivative time

Cooling coefficient

Heating/cool-

ing

Dead band

Manual reset value

Clear the offset during sta-

bilization of P or PD control.

Hysteresis (heating)

Hysteresis

settings

Hysteresis (cooling)

SP ramp set value

MV upper limit

MV lower limit

Process value

Added when Additional

PV display is ON.

Auto/manual switch

PID control only.

Added when auto/manual

select addition is ON.

Press the

OKey for

at least 3 s.

Multi-SP

set point setting

Heater current 1 value

monitor

Leakage current 1

monitor

RUN/STOP

Alarm value 1

Alarm value

upper limit 1

Alarm value

lower limit 1

Alarm value 2

Alarm value

upper limit 2

Alarm value

lower limit 2

Alarm value 3

Alarm value

upper limit 3

Alarm value

lower limit 3

MV monitor

(heating)

MV monitor

(cooling)

Press the

O and M Keys for at

least 3 s. Display flashes.

Press the

O and M Keys

for at least 1 s.

Press the

OKey

less than 1 s

Protect Level

Communications Setting Level

The time taken to move to the protect level can be

adjusted by changing the "Move to protect level

time" setting.

Starting in automatic

mode.

Process value/

set point

Displayed only for models with communications.

Changes are effective after cycling power or

after a software reset.

Operation/adjustment protect

Restricts displaying and

modifying menus in operation,

adjustment, and manual

control levels.

Initial setting/communications

protect

This protect level restricts

movement to the initial setting,

communications setting, and

advanced function setting levels.

Setting change protect

Protects changes to setups by

operating the front panel keys.

Protocol setting

Switches between CompoWay/F

(SYSWAY) and Modbus.

Communications Unit No.

Communications baud rate

CompoWay/F

(SYSWAY) only

Communications stop bits

Communications parity

Send data wait time

Set point during SP

ramp

Communications

data length

Some parameters are not displayed depending on the

model of the Controller and parameter settings. For details,

refer to the E5CZ/E5CZ-U/E5AZ/E5EZ Digital

Temperature Controllers User's Manual (Cat. No. H207).

E5CZ-R2ML 数据表(PDF) 28 Page - Omron Electronics LLC

E5CZ-R2ML 数据表(HTML) 28 Page - Omron Electronics LLC

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64

数据表下载

链接网址

E5CZ-R2ML 数据表(PDF) 28 Page - Omron Electronics LLC

E5CZ-R2ML 数据表(HTML) 28 Page - Omron Electronics LLC

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64

数据表 下载

链接网址

数据表下载