PIC16F877ATISLASHML datasheet(28/234 Pages) MICROCHIP

28 / 234 page

PIC16F87XA

DS39582B-page 26

 2003 Microchip Technology Inc.

2.2.2.5

PIR1 Register

The PIR1 register contains the individual flag bits for

the peripheral interrupts.

PIR1 REGISTER (ADDRESS 0Ch)

Note:

Interrupt flag bits are set when an interrupt

condition occurs regardless of the state of its

corresponding enable bit or the global

enable bit, GIE (INTCON<7>). User software

should ensure the appropriate interrupt bits

are clear prior to enabling an interrupt.

R/W-0

R-0

R/W-0

PSPIF(1)

ADIF

RCIF

TXIF

SSPIF

CCP1IF

TMR2IF

TMR1IF

bit 7

bit 0

bit 7

PSPIF: Parallel Slave Port Read/Write Interrupt Flag bit(1)

= A read or a write operation has taken place (must be cleared in software)

= No read or write has occurred

Note 1: PSPIF is reserved on PIC16F873A/876A devices; always maintain this bit clear.

bit 6

ADIF: A/D Converter Interrupt Flag bit

= An A/D conversion completed

= The A/D conversion is not complete

bit 5

RCIF: USART Receive Interrupt Flag bit

= The USART receive buffer is full

= The USART receive buffer is empty

bit 4

TXIF: USART Transmit Interrupt Flag bit

= The USART transmit buffer is empty

= The USART transmit buffer is full

bit 3

SSPIF: Synchronous Serial Port (SSP) Interrupt Flag bit

= The SSP interrupt condition has occurred and must be cleared in software before returning

from the Interrupt Service Routine. The conditions that will set this bit are:

• SPI – A transmission/reception has taken place.

•

I2C Slave – A transmission/reception has taken place.

•I2C Master

- A transmission/reception has taken place.

- The initiated Start condition was completed by the SSP module.

- The initiated Stop condition was completed by the SSP module.

- The initiated Restart condition was completed by the SSP module.

- The initiated Acknowledge condition was completed by the SSP module.

- A Start condition occurred while the SSP module was Idle (multi-master system).

- A Stop condition occurred while the SSP module was Idle (multi-master system).

= No SSP interrupt condition has occurred

bit 2

CCP1IF: CCP1 Interrupt Flag bit

Capture mode:

= A TMR1 register capture occurred (must be cleared in software)

= No TMR1 register capture occurred

Compare mode:

= A TMR1 register compare match occurred (must be cleared in software)

= No TMR1 register compare match occurred

PWM mode:

Unused in this mode.

bit 1

TMR2IF: TMR2 to PR2 Match Interrupt Flag bit

= TMR2 to PR2 match occurred (must be cleared in software)

= No TMR2 to PR2 match occurred

bit 0

TMR1IF: TMR1 Overflow Interrupt Flag bit

= TMR1 register overflowed (must be cleared in software)

= TMR1 register did not overflow

Legend:

R = Readable bit

W = Writable bit

U = Unimplemented bit, read as ‘0’

- n = Value at POR

‘1’ = Bit is set

‘0’ = Bit is cleared

x = Bit is unknown

PIC16F877ATI/ML 数据表(PDF) 28 Page - Microchip Technology

PIC16F877ATI/ML 数据表(HTML) 28 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载