CC2400-RTR1 datasheet(58/84 Pages) TI1

58 / 84 page

CC2400

SWRS042A

Page 58 of 83

49 Configuration Registers

The configuration of

CC2400 is done by

programming

the

16-bit

configuration

registers. The configuration data based on

selected system parameters are most

easily found by using the SmartRF® Studio

software. Complete descriptions of the

registers are given in the following tables.

After a RESET is programmed, all the

registers have default values as shown in

the tables.

Some registers are Strobe Command

Registers. Accessing these registers will

initiate the change of an internal state or

mode.

The FIFO is accessed as an 8-bit register.

Some registers contain signed values.

These are in two’s complement format. I.e.

for a 4-bit value, 0000 is 0, 1111 is –1,

1110 is –2, 1000 is -8 and 0111 is 7.

During the address transfer a status byte

is returned. This status byte is described

in Table 13 at page 23.

Overview of

CC2400 ‘s control registers

Description

0x00

MAIN

R/W

Main control register

0x01

FSCTRL

R/W

Frequency synthesiser main control and status

0x02

FSDIV

R/W

Frequency synthesiser frequency division control

0x03

MDMCTRL

R/W

Modem main control and status

0x04

AGCCTRL

R/W

AGC main control and status

0x05

FREND

R/W

Analog front-end control

0x06

RSSI

R/W

RSSI information

0x07

FREQEST

R/W

Received signal frequency offset estimation

0x08

IOCFG

R/W

I/O configuration register

0x09

Unused

0x0A

Unused

0x0B

FSMTC

R/W

Finite state machine time constants

0x0C

RESERVED

R/W

Reserved register containing spare control and status bits

0x0D

MANAND

R/W

Manual signal AND-override register

0x0E

FSMSTATE

R/W

Finite state machine information and breakpoint

0x0F

ADCTST

R/W

ADC test register

0x10

RXBPFTST

R/W

Receiver bandpass filters test register

0x11

PAMTST

R/W

PA and transmit mixers test register

0x12

LMTST

R/W

LNA and receive mixers test register

0x13

MANOR

R/W

Manual signal OR-override register

0x14

MDMTST0

R/W

Modem test register 0

0x15

MDMTST1

R/W

Modem test register 1

0x16

DACTST

R/W

DAC test register

0x17

AGCTST0

R/W

AGC test register: various control and status.

0x18

AGCTST1

R/W

AGC test register: AGC timeout.

0x19

AGCTST2

R/W

AGC test register: AGC various parameters.

0x1A

FSTST0

R/W

Test register: VCO array results and override.

0x1B

FSTST1

R/W

Test register: VC DAC manual control. VCO current constant.

0x1C

FSTST2

R/W

Test register:VCO current result and override.

0x1D

FSTST3

R/W

Test register: Charge pump current etc.

0x1E

MANFIDL

Manufacturer ID, lower 16 bit

0x1F

MANFIDH

Manufacturer ID, upper 16 bit

0x20

GRMDM

R/W

Generic radio modem control

0x21

GRDEC

R/W

Generic radio decimation control and status

0x22

PKTSTATUS

Packet mode status

1 R/W - Read/write (control/status), R - Status only, S – Strobe command register (perform action upon access)

CC2400-RTR1 数据表(PDF) 58 Page - Texas Instruments

CC2400-RTR1 数据表(HTML) 58 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84

数据表下载