X9521 datasheet(7/26 Pages) XICOR

7 / 26 page

REV 1.1.9 1/30/03

Characteristics subject to change without notice.

7 of 26

www.xicor.com

X9521

– Preliminary Information

and NVM. Therefore, the new “wiper position” setting is

recalled into the WCR after Vcc of the X9521 has been

powered down then powered back up

If WT is “0” then a DCP Volatile Write is performed. This

operation changes the DCP “wiper position” by writing

new data to the associated WCR only. The contents of the

associated NVM register remains unchanged. Therefore,

when Vcc to the device is powered down then back up,

the “wiper position” reverts to that last written to the DCP

using a nonvolatile write operation.

DCP Write Operation

A write to DCPx (x=1,2) can be performed using the three

byte command sequence shown in Figure 9.

In order to perform a write operation on a particular DCP,

the Write Enable Latch (WEL) bit of the CONSTAT Regis-

ter must ﬁrst be set (See “BL1, BL0: Block Lock protection

bits - (Nonvolatile)” on page 12.)

The Slave Address Byte 10101110 speciﬁes that a Write

to a DCP is to be conducted. An ACKNOWLEDGE is

returned by the X9521 after the Slave Address, if it has

been received correctly.

Next, an Instruction Byte is issued on SDA. Bits P1 and

P0 of the Instruction Byte determine which WCR is to be

written, while the WT bit determines if the Write is to be

volatile or nonvolatile. If the Instruction Byte format is

valid, another ACKNOWLEDGE is then returned by the

X9521.

Following the Instruction Byte, a Data Byte is issued to the

X9521 over SDA. The Data Byte contents is latched into

the WCR of the DCP on the ﬁrst rising edge of the clock

signal, after the LSB of the Data Byte (D0) has been

issued on SDA (See Figure 25).

The Data Byte determines the “wiper position” (which

FET switch of the DCP resistive array is switched ON) of

the DCP. The maximum value for the Data Byte depends

upon which DCP is being addressed (see Table below).

Using a Data Byte larger than the values speciﬁed above

results in the “wiper terminal” being set to the highest tap

position. The “wiper position” does NOT roll-over to the

lowest tap position.

For DCP2 (256 Tap), the Data Byte maps one to one to

the “wiper position” of the DCP “wiper terminal”. There-

fore, the Data Byte 00001111 (1510) corresponds to set-

ting the “wiper terminal” to tap position 15. Similarly, the

Data Byte 00011100 (2810) corresponds to setting the

WT†

Description

Select a Volatile Write operation to be performed

on the DCP pointed to by bits P1 and P0

Select a Nonvolatile Write operation to be per-

formed on the DCP pointed to by bits P1 and P0

WRITE TYPE

DCP SELECT

†

This bit has no effect when a Read operation is being performed.

Figure 8.

Instruction Byte Format

10101110

P1 P0

SLAVE ADDRESS BYTE

INSTRUCTION BYTE

DATA BYTE

Figure 9.

DCP Write Command Sequence

P1- P0

DCPx

# Taps

Max. Data Byte

Reserved

x=1

100

Refer to Appendix 1

x=2

256

FFh

Reserved

X9521 数据表(PDF) 7 Page - Xicor Inc.

X9521 数据表(HTML) 7 Page - Xicor Inc.

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26

数据表下载