STM32F101XF datasheet(18/117 Pages) STMICROELECTRONICS

18 / 117 page

Description

STM32F101xF, STM32F101xG

18/117

DocID16553 Rev 5

2.3.14

Voltage regulator

The regulator has three operation modes: main (MR), low power (LPR) and power down.

•

MR is used in the nominal regulation mode (Run)

•

LPR is used in the Stop modes.

•

Power down is used in Standby mode: the regulator output is in high impedance: the

kernel circuitry is powered down, inducing zero consumption (but the contents of the

registers and SRAM are lost)

This regulator is always enabled after reset. It is disabled in Standby mode.

2.3.15

Low-power modes

The STM32F101xF and STM32F101xG access line supports three low-power modes to

achieve the best compromise between low-power consumption, short startup time and

available wakeup sources:

•

Sleep mode

In Sleep mode, only the CPU is stopped. All peripherals continue to operate and can

wake up the CPU when an interrupt/event occurs.

•

Stop mode

Stop mode achieves the lowest power consumption while retaining the content of

SRAM and registers. All clocks in the 1.8 V domain are stopped, the PLL, the HSI RC

and the HSE crystal oscillators are disabled. The voltage regulator can also be put

either in normal or in low-power mode.

The device can be woken up from Stop mode by any of the EXTI line. The EXTI line

source can be one of the 16 external lines, the PVD output or the RTC alarm.

•

Standby mode

The Standby mode is used to achieve the lowest power consumption. The internal

voltage regulator is switched off so that the entire 1.8 V domain is powered off. The

PLL, the HSI RC and the HSE crystal oscillators are also switched off. After entering

Standby mode, SRAM and register contents are lost except for registers in the Backup

domain and Standby circuitry.

The device exits Standby mode when an external reset (NRST pin), a IWDG reset, a

rising edge on the WKUP pin, or an RTC alarm occurs.

Note:

The RTC, the IWDG, and the corresponding clock sources are not stopped by entering Stop

or Standby mode.

2.3.16

DMA

The flexible 12-channel general-purpose DMAs (7 channels for DMA1 and 5 channels for

DMA2) are able to manage memory-to-memory, peripheral-to-memory and memory-to-

peripheral transfers.

The two DMA controllers support circular buffer management, removing the need for user

code intervention when the controller reaches the end of the buffer.

Each channel is connected to dedicated hardware DMA requests, with support for software

trigger on each channel. Configuration is made by software and transfer sizes between

source and destination are independent.

DMA can be used with the main peripherals: SPI, I2C, USART, general-purpose and basic

timers TIMx, DAC and ADC.

STM32F101XF 数据表(PDF) 18 Page - STMicroelectronics

STM32F101XF 数据表(HTML) 18 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载