PIC12CE673 datasheet(37/116 Pages) MICROCHIP

37 / 116 page

Preliminary

DS40181B-page 37

PIC12CE67X

FIGURE 8-1:

ADCON0 REGISTER (ADDRESS 1Fh)

R/W-0

ADCS1 ADCS0

CHS1

CHS0

GO/DONE

ADON

R = Readable bit

W = Writable bit

U = Unimplemented bit,

read as ‘0’

- n = Value at POR reset

bit7

bit0

bit 7-6:

ADCS1:ADCS0: A/D Conversion Clock Select bits

= FOSC/2

= FOSC/8

= FOSC/32

= FRC (clock derived from an RC oscillation)

bit 5:

Reserved

bit 4-3: CHS1:CHS0: Analog Channel Select bits

= channel 0, (GP0/AN0)

= channel 1, (GP1/AN1)

= channel 2, (GP2/AN2)

= channel 3, (GP4/AN3)

bit 2:

GO/DONE: A/D Conversion Status bit

If ADON = 1

1 = A/D conversion in progress (setting this bit starts the A/D conversion)

0 = A/D conversion not in progress (This bit is automatically cleared by hardware when the A/D conver-

sion is complete)

bit 1:

Reserved

bit 0:

ADON: A/D On bit

1 = A/D converter module is operating

0 = A/D converter module is shutoff and consumes no operating current

8.0

ANALOG-TO-DIGITAL

CONVERTER (A/D) MODULE

The analog-to-digital (A/D) converter module has four

analog inputs.

The A/D allows conversion of an analog input signal to

a corresponding 8-bit digital number (refer to Applica-

tion Note AN546 for use of A/D Converter). The output

of the sample and hold is the input into the converter,

which generates the result via successive approxima-

tion. The analog reference voltage is software select-

able to either the device’s positive supply voltage (VDD)

or the voltage level on the GP1/AN1/VREF pin. The A/D

converter has a unique feature of being able to operate

while the device is in SLEEP mode.

The A/D module has three registers. These registers

are:

• A/D Result Register (ADRES)

• A/D Control Register 0 (ADCON0)

• A/D Control Register 1 (ADCON1)

The ADCON0 register, shown in Figure 8-1, controls

the operation of the A/D module. The ADCON1 regis-

ter, shown in Figure 8-2, conﬁgures the functions of the

port pins. The port pins can be conﬁgured as analog

inputs (GP1 can also be a voltage reference) or as dig-

ital I/O.

Note:

If the port pins are conﬁgured as analog

inputs (reset condition), reading the port

(MOVF GP,W) results in reading '0's.

Note:

Changing ADCON1 register can cause the

GPIF and INTF ﬂags to be set in the

INTCON register. These interrupts should

be disabled prior to modifying ADCON1.

PIC12CE673 数据表(PDF) 37 Page - Microchip Technology

PIC12CE673 数据表(HTML) 37 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载