MB9BF412RPMC-G-JNE2 datasheet(2/112 Pages) CYPRESS

2 / 112 page

Document Number: 002-05615 Rev. *D

Page

2 of 112

MB9B410R Series

LIN



LIN protocol Rev.2.1 supported



Full-duplex double buffer



Master/Slave mode supported



LIN break field generate (can be changed 13 to 16-bit

length)



LIN break delimiter generate (can be changed 1 to 4-bit

length)



Various error detect functions available (parity errors,

framing errors, and overrun errors)

I2C



Standard-mode (Max 100 kbps) / Fast-mode (Max 400

kbps) supported

DMA Controller (Eight channels)

DMA Controller has an independent bus for CPU, so CPU

and DMA Controller can process simultaneously.

8 independently configured and operated channels

Transfer can be started by software or request from the

built-in peripherals

Transfer address area: 32-bit (4 Gbyte)

Transfer mode: Block transfer/Burst transfer/Demand

transfer

Transfer data type: byte/half-word/word

Transfer block count: 1 to 16

Number of transfers: 1 to 65536

A/D Converter (Max 16 channels)

12-bit A/D Converter



Successive Approximation Register type



Built-in 3 unit



Conversion time: 1.0 μs @ 5 V



Priority conversion available (priority at 2 levels)



Scanning conversion mode



Built-in FIFO for conversion data storage (for SCAN

conversion: 16 steps, for Priority conversion: 4 steps)

Base Timer (Max eight channels)

Operation mode is selectable from the followings for each

channel.

16-bit PWM timer

16-bit PPG timer

16-/32-bit reload timer

16-/32-bit PWC timer

General Purpose I/O Port

This series can use its pins as general purpose I/O ports

when they are not used for external bus or peripherals.

Moreover, the port relocate function is built in. It can set

which I/O port the peripheral function can be allocated.

Capable of pull-up control per pin

Capable of reading pin level directly

Built-in the port relocate function

Up 103 fast general purpose I/O Ports @ 120 pin Package

Some pin is 5 V tolerant I/O.

See "4 List of Pin Functions" to confirm the corresponding

pins.

Multi-function Timer (Max three units)

The Multi-function timer is composed of the following blocks.

16-bit free-run timer × 3 ch./unit

Input capture × 4 ch./unit

Output compare × 6 ch./unit

A/D activating compare × 3 ch./unit

Waveform generator × 3 ch./unit

16-bit PPG timer × 3 ch./unit

The following function can be used to achieve the motor

control.

PWM signal output function

DC chopper waveform output function

Dead time function

Input capture function

A/D convertor activate function

DTIF (Motor emergency stop) interrupt function

Real-time clock (RTC)

The Real-time clock can count

Year/Month/Day/Hour/Minute/Second/A day of the week from

00 to 99.

Interrupt function with specifying date and time

(Year/Month/Day/Hour/Minute) is available. This function is

also available by specifying only Year, Month, Day, Hour or

Minute.

Timer interrupt function after set time or each set time.

Capable of rewriting the time with continuing the time count.

Leap year automatic count is available.

MB9BF412RPMC-G-JNE2 数据表(PDF) 2 Page - Cypress Semiconductor

MB9BF412RPMC-G-JNE2 数据表(HTML) 2 Page - Cypress Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载