PIC18LF4520ESLASHSPQTP datasheet(122/390 Pages) MICROCHIP

122 / 390 page

PIC18F2420/2520/4420/4520

DS39631A-page 120

Preliminary

 2004 Microchip Technology Inc.

10.6

Parallel Slave Port

In addition to its function as a general I/O port, PORTD

can also operate as an 8-bit wide Parallel Slave Port

(PSP) or microprocessor port. PSP operation is con-

trolled by the 4 upper bits of the TRISE register

(Register 10-1).

Setting

control

bit,

PSPMODE

(TRISE<4>), enables PSP operation as long as the

enhanced CCP module is not operating in dual output

or quad output PWM mode. In Slave mode, the port is

asynchronously readable and writable by the external

world.

The PSP can directly interface to an 8-bit micro-

processor data bus. The external microprocessor can

read or write the PORTD latch as an 8-bit latch. Setting

the control bit, PSPMODE, enables the PORTE I/O

pins to become control inputs for the microprocessor

port. When set, port pin RE0 is the RD input, RE1 is the

WR input and RE2 is the CS (Chip Select) input. For

this functionality, the corresponding data direction bits

of the TRISE register (TRISE<2:0>) must be config-

ured as inputs (set). The A/D port configuration bits,

PFCG3:PFCG0 (ADCON1<3:0>), must also be set to a

value in the range of ‘1010’ through ‘1111’.

A write to the PSP occurs when both the CS and WR

lines are first detected low and ends when either are

detected high. The PSPIF and IBF flag bits are both set

when the write ends.

A read from the PSP occurs when both the CS and RD

lines are first detected low. The data in PORTD is read

out and the OBF bit is clear. If the user writes new data

to PORTD to set OBF, the data is immediately read out;

however, the OBF bit is not set.

When either the CS or RD lines are detected high, the

PORTD pins return to the input state and the PSPIF bit

is set. User applications should wait for PSPIF to be set

before servicing the PSP; when this happens, the IBF

and OBF bits can be polled and the appropriate action

taken.

The timing for the control signals in Write and Read

modes is shown in Figure 10-3 and Figure 10-4,

respectively.

FIGURE 10-2:

PORTD AND PORTE

BLOCK DIAGRAM

(PARALLEL SLAVE PORT)

Note:

The Parallel Slave Port is only available on

40/44-pin devices.

Data Bus

WR LATD

RDx pin

RD PORTD

One bit of PORTD

Set Interrupt Flag

PSPIF (PIR1<7>)

Read

Chip Select

Write

TTL

WR PORTD

RD LATD

Data Latch

Note:

I/O pins have diode protection to VDD and VSS.

PORTE Pins

PIC18LF4520E/SPQTP 数据表(PDF) 122 Page - Microchip Technology

PIC18LF4520E/SPQTP 数据表(HTML) 122 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载