11

SEL

Setpoint 2

Enable

Setpoint

Select

Setpoint

Assignment

Setpoint

Output Logic

Setpoint

Output

Action

Setpoint

Value

Setpoint

Output

Time-out

SP2 Only

Setpoint

Annunciator

SPt SEL

4-SEtPt

SP2 Enb

SPn ASN

SPn ACt

SPn tOUt

SPn VAL

SPn OUt

SPn LIt

PPrroo

SPn P-UP

SPn StbY

Setpoint

Standby

Operation

Setpoint

Boundary

Type

SPn tYPE

Counter

Auto Reset

SPn AUtO

SPn ChC

Change Display

Color with

Output State

SP2 Output

Off at SP1

Output

SP1 Output

Off at SP2

Output

SP1 OFF2

SP2 OFF1

Setpoint

Output Reset

with Manual

Reset

SPn rSt

Setpoint Output

Power-up

State

SP1 Only

SP2 Only

Backlight

Unit Only

PARAMETER MENU

The Setpoint Output Parameters are only active when an optional Setpoint

Output Module is installed in the meter. Some parameters in the menu will not

appear depending on the Setpoint Assignment and Setpoint Output Action. The

Setpoint Parameter Availability chart below illustrates this.

PARAMETER

DESCRIPTION

BOUNDARY

bOUNd

LATCH

LAtCH

RATE ASSIGNMENT

TIMED OUT

t-OUt

BOUNDARY

bOUNd

LATCH

LAtCH

Yes

No

No

Yes

No

No

SPn VAL

Setpoint Value

Yes

Yes

Yes

Yes

Yes

Yes

SPn OUt

Setpoint Output Logic

Yes

Yes

Yes

Yes

Yes

Yes

SPn LIt

Setpoint Annunciator

Yes

Yes

Yes

Yes

Yes

Yes

SPn P-UP

Setpoint Output Power-up State

No

No

Yes

No

No

Yes

SPn tYPE

Setpoint Boundary Type

No

Yes

No

Yes

Yes

Yes

SPn StbY

Standby Operation (Low acting only)

No

Yes

No

Yes

Yes

Yes

SPn AUtO

Counter Auto Reset

Yes

No

Yes

No

No

No

SP1 OFF2

SP1 Output Off at SP2 (SP1 only)

Yes

No

Yes

No

No

No

SP2 OFF1

SP2 Output Off at SP1 (SP2 only)

Yes

No

Yes

No

No

No

SPn rSt

Output Reset with Manual Reset

Yes

No

Yes

Yes

No

Yes

SPn ChC

Change Display Color w/ Output State

Yes

Yes

Yes

Yes

Yes

Yes

Setpoint Output Time-out Value

TIMED OUT

t-OUt

COUNTER ASSIGNMENT (A or B) *

SPn tOUt

* BOUNDARY Setpoint Action not applicable for Counter B Assignment

Select the Setpoint Output to be programmed, starting with Setpoint 1. The

steps for Setpoint 2 if both Setpoints are used in the application.

available is dependent on the Setpoint option module installed.

SETPOINT SELECT

SP2

SP1

NO





NO

SPt SEL

SETPOINT 2 ENABLE (SP2 Only)

YES

NO





NO

SP2 Enb

SETPOINT ASSIGNMENT

SETPOINT PARAMETER AVAILABILITY

Select the display to which the Setpoint is assigned.





Count A

SPn ASN

SETPOINT OUTPUT ACTION

The parameter selects the action of the Setpoint Output as described in the

chart. Boundary output action is not applicable for Counter B assignment.





LAtCH

SPn ACt

Count A

Count b

rAtE

LAtCH

t-OUt

bOUNd

SPT ACTION DESCRIPTION

OUTPUT ACTIVATES OUTPUT DEACTIVATES

LAtCH

Latched Output Mode

When Count =

Setpoint

At Manual Reset

t-OUt

Timed Output Mode

When Count =

Setpoint

After Setpoint

Output Time-Out

bOUNd

Boundary Mode

(Low Acting Type)

Boundary Mode

(High Acting Type)

Setpoint

Setpoint

When Count

When Count

< Setpoint