CUB5COM2 datasheet(12/16 Pages) REDLION

12 / 16 page

SAVE

will restore the output to the same state it was at before the meter was

powered down. ON will activate the output at power up. OFF will deactivate the

output at power up.

SETPOINT OUTPUT POWER-UP STATE

SETPOINT VALUE

Enter the desired Setpoint value. To enter a negative setpoint value,

increment digit 8 to display a “-” sign (Counter A only).

This parameter automatically resets the counter to which the setpoint is

assigned (SPn ASN) each time the setpoint value is reached. The automatic reset

can occur at output start, or at output end if the Setpoint Output Action is

programmed for timed output mode. The Reset-to-Count Load selections

(“CtLd-”) only apply to Counter A assignment. This reset may be different from

the Counter A Reset Action selected in Module 1.

COUNTER AUTO RESET

Selecting YES causes the Setpoint output to deactivate (reset) when the

Setpoint Assigned Counter is reset. The counter reset can occur by the RST

button, User Input, Counter Reset at Power-up or a serial Reset Counter

command.

This output reset will not occur when the Assigned Counter is reset by a

Setpoint generated Counter Auto Reset.

SETPOINT OUTPUT RESET WITH MANUAL RESET

This parameter enables the backlight CUB5 to switch the backlight color when

the output state changes. This parameter is only active for the backlight version.

CHANGE DISPLAY COLOR WITH OUTPUT STATE

Count A:

to 999999

Rate:

to 9999999

Count B:





00000100

SPn VAL

SETPOINT OUTPUT TIME-OUT

This parameter is only active if the Setpoint Action is set to time out (t-OUt).

Enter the value in seconds that the Setpoint output will be active, once the

Setpoint Value is reached.





001.00

SPn tOUt

SETPOINT OUTPUT LOGIC

Normal (NOr) turns the output “on” when activated and “off” when

deactivated. Reverse (rEV) turns the output “off” when activated and “on” when

deactivated.





NOr

SPn OUt

SETPOINT ANNUNCIATOR

Normal (NOr) displays the setpoint annunciator when the corresponding

output is “on”. Reverse (rEV) displays the setpoint annunciator when the output

is “off”.





NOr

SPn LIt





OFF

SPn P-UP





SPn AUtO





YES

SPn rSt





SPn ChC

CtLd-Str

@2Ero-Str

CtLd-End

2Ero-End

YES

SAVE

OFF

SETPOINT BOUNDARY TYPE

High Acting Boundary Type activates the output when the assigned display

value (SPn ASN) equals or exceeds the Setpoint value. Low Acting activates the

output when the assigned display value is less than or equal to the Setpoint.





HI-ACt

SPn tYPE

SETPOINT STANDBY OPERATION

This parameter only applies to Low Acting Boundary Type setpoints. Select

YES

to disable a Low Acting Setpoint at power-up, until the assigned display

value crosses into the output “off” area. Once in the output “off” area, the

Setpoint will then function per the description for Low Acting Boundary Type.





SPn StbY

SETPOINT 1 OUTPUT OFF AT SETPOINT 2 (SP1 Only)

This parameter will deactivate Setpoint 1 output at the Start or End of

Setpoint 2 output (O1 off at O2). The “-End” setting only applies if Setpoint 2

Output Action is programmed for timed output.





SP1 OFF2

SETPOINT 2 OUTPUT OFF AT SETPOINT 1 (SP2 Only)

This parameter will deactivate Setpoint 2 output at the Start or End of

Setpoint 1 output (O2 off at O1). The “-End” setting only applies if Setpoint 1

Output Action is programmed for timed output.





SP2 OFF1

0.01

to 599.99 seconds

NOr

rEV

NOr

rEV

HI-ACt

LO-ACt

YES

SELECTION ACTION

No Auto Reset.

2Ero-Str

Reset to Zero at the start of output activation.

CtLd-Str

Reset to Count Load value at the start of output activation.

2Ero-End

Reset to Zero at the end of output activation (timed out only).

CtLd-End

Out2-Str

Out2-End

Out1-End

Out1-Str

YES

Reset to Count Load value at the end of output activation

(timed out only).

9999999

to 99999999

CUB5COM2 数据表(PDF) 12 Page - Red Lion Controls. Inc

CUB5COM2 数据表(HTML) 12 Page - Red Lion Controls. Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

数据表下载