AD4022BCPZ-R2 datasheet(33/39 Pages) AD

33 / 39 page

Data Sheet

AD4020/AD4021/AD4022

Rev. B | Page 33 of 39

CS MODE, 4-WIRE TURBO MODE

This mode is typically used when a single AD4020/4021/4022

device is connected to an SPI-compatible digital host. Turbo

mode allows lower SCK frequencies by increasing the time that the

ADC conversion result can be clocked out. The AD4020 can

achieve a throughput rate of 1.8 MSPS only when turbo mode is

enabled and using a minimum SCK frequency of 71 MHz (see the

Serial Clock Frequency Requirements section). The connection

diagram is shown in Figure 59, and the corresponding timing

diagram is shown in Figure 60.

To enable turbo mode, set the turbo mode enable bit in the

configuration register to 1 (see Table 12). This mode replaces the

4-wire with busy indicator mode when turbo mode is enabled. The

digital host must be able to write data over SDI to perform register

reads and writes (see the Register Read/Write Functionality

section). When turbo mode is enabled, the conversion result read

on SDO corresponds to the result of the previous conversion.

A rising edge on CNV initiates a conversion and forces SDO to

high impedance. CNV must be held high throughout the

conversion and data readback phase. When performing

conversions in this mode, SDI must be high during the CNV

rising edge. The user must wait tQUIET1 time after the CNV rising

edge before bringing SDI low to clock out the previous conversion

result. When the conversion is complete (after tCONV), the AD4020/

AD4021/AD4022 enter the acquisition phase and power down.

SDI is analogous to a chip select input, and bringing SDI low

outputs the MSB of the conversion result on SDO. The remaining

data bits are clocked out on SDO by subsequent SCK falling

edges. The data is valid on both SCK edges. Although the rising

edge can capture the data, a digital host using the SCK falling

edge allows a faster reading rate, provided it has an acceptable

hold time, as dictated by tHSDO (see Table 2). The conversion

result is clocked out on SDO on the first 20 SCK falling edges. If

the status bits are enabled, they are shifted out on SDO on the

21st through the 26th SCK falling edges (see the Status Bits section).

SDO returns to high impedance after the final SCK falling edge,

or when CNV goes high (whichever occurs first). The user must

also provide a delay of tQUIET2 between the final SCK falling edge

and the next CNV rising edge to ensure specified performance.

AD4020/

AD4021/

AD4022

SDI

SDO

CNV

SCK

CONVERT

DATA IN

CLK

DIGITAL HOST

DATA OUT

Figure 59. CS Mode, 4-Wire Turbo Mode Connection Diagram

ACQUISITION

SDO

SCK

ACQUISITION

SDI

CNV

tSSDICNV

tHSDICNV

tCYC

tSCK

tSCKL

tEN

tHSDO

tDSDO

tDIS

tSCKH

D19

D18

D17

tQUIET1

tQUIET2

tACQ

CONVERSION

tCONV

Figure 60. CS Mode, 4-Wire Turbo Mode Timing Diagram (Status Bits Not Shown)

AD4022BCPZ-R2 数据表(PDF) 33 Page - Analog Devices

AD4022BCPZ-R2 数据表(HTML) 33 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39

数据表下载