IMX6SDLCEC datasheet(13/169 Pages) NXP

13 / 169 page

Modules List

i.MX 6Solo/6DualLite Applications Processors for Consumer Products, Rev. 9, 11/2018

NXP Semiconductors

EPDC

Electrophoretic Display

Controller

Peripherals

The EPDC is a feature-rich, low power, and

high-performance direct-drive, active matrix EPD

controller. It is specifically designed to drive E-INK

™

EPD panels, supporting a wide variety of TFT

backplanes. It is available in both i.MX 6DualLite and

i.MX 6Solo.

EPIT-1

EPIT-2

Enhanced Periodic

Interrupt Timer

Timer Peripherals

Each EPIT is a 32-bit “set and forget” timer that starts

counting after the EPIT is enabled by software. It is

capable of providing precise interrupts at regular

intervals with minimal processor intervention. It has a

12-bit prescaler for division of input clock frequency to

get the required time setting for the interrupts to occur,

and counter value can be programmed on the fly.

ESAI

Enhanced Serial Audio

Interface

Connectivity

Peripherals

The Enhanced Serial Audio Interface (ESAI) provides a

full-duplex serial port for serial communication with a

variety of serial devices, including industry-standard

codecs, SPDIF transceivers, and other processors.

The ESAI consists of independent transmitter and

receiver sections, each section with its own clock

generator. All serial transfers are synchronized to a

clock. Additional synchronization signals are used to

delineate the word frames. The normal mode of

operation is used to transfer data at a periodic rate, one

word per period. The network mode is also intended for

periodic transfers; however, it supports up to 32 words

(time slots) per period. This mode can be used to build

time division multiplexed (TDM) networks. In contrast,

the on-demand mode is intended for non-periodic

transfers of data and to transfer data serially at high

speed when the data becomes available.

The ESAI has 12 pins for data and clocking connection

to external devices.

FlexCAN-1

FlexCAN-2

Flexible Controller Area

Network

Connectivity

Peripherals

The CAN protocol was primarily, but not only, designed

to be used as a vehicle serial data bus, meeting the

specific requirements of this field: real-time processing,

reliable operation in the Electromagnetic interference

(EMI) environment of a vehicle, cost-effectiveness and

required bandwidth. The FlexCAN module is a full

implementation of the CAN protocol specification,

Version 2.0 B, which supports both standard and

extended message frames.

512x8 Fuse Box

Electrical Fuse Array

Security

Electrical Fuse Array. Enables to setup Boot Modes,

Security Levels, Security Keys, and many other system

parameters.

The i.MX 6Solo/6DualLite processors consist of

512x8-bit fuse fox accessible through OCOTP_CTRL

interface.

Table 2. i.MX 6Solo/6DualLite Modules List (continued)

Block Mnemonic

Block Name

Subsystem

Brief Description

IMX6SDLCEC 数据表(PDF) 13 Page - NXP Semiconductors

IMX6SDLCEC 数据表(HTML) 13 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载

链接网址

IMX6SDLCEC 数据表(PDF) 13 Page - NXP Semiconductors

IMX6SDLCEC 数据表(HTML) 13 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表 下载

链接网址

数据表下载