H5AN4G4NAFR-RDC datasheet(28/45 Pages) HYNIX

28 / 45 page

Rev. 1.3 / Mar.2016

Table 9 - IDD4WC Measurement-Loop Pattern1

NOTE :

1. DQS_t, DQS_c are VDDQ.

2. BG1 is don’t care for x16 device.

3. C[2:0] are used only for 3DS device.

4. Burst Sequence driven on each DQ signal by Write Command.

Datad

0 0

D0=00, D1=FF

D2=FF, D3=00

D4=FF, D5=00

D6=00, D7=FF

D8=CRC

1,2

D, D

0 0

3,4

D#, D#

0 32 3 0 0 0 7 F 0

1 1

D0=FF, D1=00

D2=00, D3=FF

D4=00, D5=FF

D6=FF, D7=00

D8=CRC

6,7

D, D

0 0

8,9

D#, D#

0 32 3 0 0 0 7 F 0

2 10-14

repeat Sub-Loop 0, use BG[1:0]2 = 0, BA[1:0] = 2 instead

3 15-19

repeat Sub-Loop 1, use BG[1:0]2 = 1, BA[1:0] = 3 instead

4 20-24

repeat Sub-Loop 0, use BG[1:0]2 = 0, BA[1:0] = 1 instead

5 25-29

repeat Sub-Loop 1, use BG[1:0]2 = 1, BA[1:0] = 2 instead

6 30-34

repeat Sub-Loop 0, use BG[1:0]2 = 0, BA[1:0] = 3 instead

7 35-39

repeat Sub-Loop 1, use BG[1:0]2 = 1, BA[1:0] = 0 instead

8 40-44

repeat Sub-Loop 0, use BG[1:0]2 = 2, BA[1:0] = 0 instead

For x4 and x8 only

9 45-49

repeat Sub-Loop 1, use BG[1:0]2 = 3, BA[1:0] = 1 instead

10 50-54

repeat Sub-Loop 0, use BG[1:0]2 = 2, BA[1:0] = 2 instead

11 55-59

repeat Sub-Loop 1, use BG[1:0]2 = 3, BA[1:0] = 3 instead

12 60-64

repeat Sub-Loop 0, use BG[1:0]2 = 2, BA[1:0] = 1 instead

13 65-69

repeat Sub-Loop 1, use BG[1:0]2 = 3, BA[1:0] = 2 instead

14 70-74

repeat Sub-Loop 0, use BG[1:0]2 = 2, BA[1:0] = 3 instead

15 75-79

repeat Sub-Loop 1, use BG[1:0]2 = 3, BA[1:0] = 0 instead

H5AN4G4NAFR-RDC 数据表(PDF) 28 Page - Hynix Semiconductor

H5AN4G4NAFR-RDC 数据表(HTML) 28 Page - Hynix Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45

数据表下载