A22Z-R datasheet(43/52 Pages) OMRON

43 / 52 page

A22E

Installation

Mounting to the Panel

Assembling the Cap

(1) Preparing the Panel

(2) Mounting the Operation Unit on the Panel

• The panel dimensions are shown below.

• The panel thickness must be 1 to 5 mm.

• Always use a 25-mm-dia. A22Z-R25 Lock Ring for a 25-mm-dia. hole.

IP65 degree of protection will be lost if the 25-mm-dia. Lock Ring is not used

because of the larger size of a 25-mm-dia. hole.

• When painting or coating the panel, make sure that the specified panel

dimensions apply to the panel after painting or coating.

• Insert the Operation Unit from the front surface of the panel, insert the Lock

Ring and the Tightening Nut from the terminal side, then tighten the Ring.

Before tightening, check that the rubber washer is present between the

Operation Unit and the panel.

• Align the Lock Ring with the groove in the casing, then insert the Lock Ring so

that its edge is located on the panel side.

• Tighten the Tightening Nut at a torque of 1.0 to 2.0 N·m.

• When using a Lock Ring, replace with the supplied Lock Ring, insert the

projecting part into the lock slot, and then tighten the Tightening Nut.

(3) Mounting the Switch on the Operation Unit

• Insert the Operation Unit into the Switch Unit, aligning the arrow mark inscribed

on the Case with the lever on the Switch Blocks, then move the lever in the

direction indicated by the arrow in the following figure.

(4) Removing the Switch

Emergency Stop Switch

• Insert the protrusion of the Tightening Wrench (A22Z-3905) into the Cap slot and then turn to remove the Cap.

22.3

dia.

+0.4

dia.

+0.5

22.3

dia.

+0.4

24.1

+0.4

3.2

R0.8 max.

With Lock Ring

Without Lock Ring

+0.2

Hold here

Tightening Nut

Lock Ring

Rubber Washer

Panel

Lock Ring

Projecting

part

1. When the panel cutout dimension is

25 dia., remove the supplied rubber

washer and mount the 25-dia. Ring as

shown below. (Since the A22Z-R25 is

not attached to the main body, order

separately.) When using a Legend

Plate (Order Separately), do not

remove the rubber washer.

22 dia.

22.3 dia.

25 dia.

22.3 dia.

0.5

1.3

Panel

Lock Ring

Tightening Nut

25-dia. Ring

(A22Z-R25)

Operation Unit

Rubber washer

(mounted to

Operation Unit)

When not using a

Legend Plate,

remove the rubber

washer.

(If required)

Legend Plates for

Emergency Stop

(order separately)

2. When the panel cutout

dimension is 30 dia., use resin

attachment A22Z-A30. Since it

is not attached to the main

body, order separately.

Operation Unit

Rubber washer

(mounted to

Operation Unit)

30-dia.

Resin Attachment

(A22Z-A30)

Rubber washer

(included)

Mounting

panel

Lock Ring

Tightening Nut

Lever

Arrow mark

Operation

Unit

• Move the lever in the direction indicated by the arrow in the following figure,

then pull the Operation Unit or the Switch Blocks.

Since the lever has a hole with an inside diameter of 6.5 mm, the lever can

be moved in the specified direction by inserting a screwdriver into the hole

and then moving the screwdriver.

Screwdriver

Cap slot

Protrusion

A22Z-R 数据表(PDF) 43 Page - Omron Electronics LLC

A22Z-R 数据表(HTML) 43 Page - Omron Electronics LLC

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52

数据表下载

链接网址

A22Z-R 数据表(PDF) 43 Page - Omron Electronics LLC

A22Z-R 数据表(HTML) 43 Page - Omron Electronics LLC

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52

数据表 下载

链接网址

数据表下载