ICS1893AF datasheet(38/137 Pages) RENESAS

38 / 137 page

ICS1893AF, Rev D 10/26/04

October, 2004

Chapter 7

Functional Blocks

ICS1893AF Data Sheet - Release

7.2.4

Auto-Negotiation: Reset and Restart

If enabled, execution of the ICS1893AF auto-negotiation process occurs at power-up and upon

management request. There are two primary ways to begin the Auto-Negotiation state machine:

• ICS1893AF reset

• Auto-Negotiation Restart

7.2.4.1

Auto-Negotiation Reset

During a reset, the ICS1893AF initializes its Auto-Negotiation sublayer modules to their default states.

(That is, the Auto-Negotiation Arbitration State Machine and the Auto-Negotiation Progress Monitor reset to

their idle states.) In addition, the Auto-Negotiation Progress Monitor status bits are all set to logic zero. This

action occurs for any type of reset (hardware reset, software reset, or power-on reset).

7.2.4.2

Auto-Negotiation Restart

As with a reset, during an Auto-Negotiation restart, the ICS1893AF initializes the Auto-Negotiation

Arbitration State Machine and the Auto-Negotiation Progress Monitor modules to their default states.

However, during an Auto-Negotiation Restart, the Auto-Negotiation Progress Monitor status bits maintain

their current state. Only three events can alter the state of the Auto-Negotiation Progress Monitor status

bits after a Restart: (1) an STA read operation, (2) a reset, or (3) the Auto-Negotiation Arbitration State

Machine progressing to a higher state or value.

The Auto-Negotiation Progress Monitor Status bits change only if they are progressing to a state with a

value greater than their current state (that is, a state with a higher logical value than that of their current

state). For a detailed explanation of these bits and their operation, see Section 7.2.5, “Auto-Negotiation:

Progress Monitor”.

After the Auto-Negotiation Arbitration State Machine reaches its final state (which is Auto-Negotiation

Complete), only an STA read of the QuickPoll Detailed Status Register or an ICS1893AF reset can alter

these status bits.

Any of the following situations initiates a restart of the ICS1893AF Auto-Negotiation sublayer:

• A link failure

• In software mode:

– Writing a logic one to the Control Register’s Restart Auto-Negotiation bit (bit 0.9), which is a self-

clearing bit.

– Toggling the Control Register’s Auto-Negotiation Enable bit (bit 0.12) from a logic one to a logic zero,

and back to a logic one.

7.2.5

Auto-Negotiation: Progress Monitor

Under typical circumstances, the Auto-Negotiation sublayer can establish a connection with the

ICS1893AF’s remote link partner. However, some situations can prevent the auto-negotiation process from

properly achieving this goal. For these situations, the ICS1893AF has an Auto-Negotiation Progress

Monitor to provide detailed status information to its Station Management (STA) entity. With this status

information, the STA can diagnose the failure mechanism and – in some situations – establish the link by

correcting the problem.

When enabled, the auto-negotiation process typically requires less than 500 ms to execute, independent of

the link partner's ability to perform the auto-negotiation process. Typically, an STA polls both the

Auto-Negotiation Complete bit (bit 1.5) and the Link Status bit (bit 1.2) to determine when a link is

successfully established, either through auto-negotiation or parallel detection. The STA can then poll the

Auto-Negotiation Link Partner Ability Register and determine the highest-performance operating mode in

common with the capabilities it is advertising.

ICS1893AF 数据表(PDF) 38 Page - Renesas Technology Corp

ICS1893AF 数据表(HTML) 38 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载