ICS1893AF datasheet(60/137 Pages) RENESAS

60 / 137 page

ICS1893AF, Rev D 10/26/04

October, 2004

Chapter 8

Management Register Set

ICS1893AF Data Sheet - Release

8.2.2

Loopback Enable (bit 0.14)

This bit controls the Loopback mode for the ICS1893AF. Setting this bit to logic:

• Zero disables the Loopback mode.

• One enables the Loopback mode by disabling the Twisted-Pair Transmitter, the Twisted-Pair Receiver,

and the collision detection circuitry. (The STA can override the ICS1893AF from disabling the collision

detection circuitry in Loopback mode by writing logic one to bit 0.7.) When the ICS1893AF is in Loopback

mode, the data presented at the MAC/repeater transmit interface is internally looped back to the

MAC/repeater receive interface. The delay from the assertion of Transmit Data Enable (TXEN) to the

assertion of Receive Data valid (RXDV) is less than 512 bit times.

8.2.3

Data Rate Select (bit 0.13)

This bit provides a means of controlling the ICS1893AF data rate. Its operation depends on the state of

several other functions, including the HW/SW input pin and the Auto-Negotiation Enable bit (bit 0.12).

When the ICS1893AF is configured for:

• Hardware mode (that is, the HW/SW pin is logic zero), the ICS1893AF isolates this bit 0.13 and uses the

10/100SEL input pin to establish the data rate for the ICS1893AF. In this Hardware mode:

– Bit 0.13 is undefined.

– The ICS1893AF provides a Data Rate Status bit (in the QuickPoll Detailed Status Register, bit 17.15),

which always shows the setting of an active link.

• Software mode (that is, the HW/SW pin is logic one), the function of bit 0.13 depends on the

Auto-Negotiation Enable bit 0.12. When the Auto-Negotiation sublayer is:

– Enabled, the ICS1893AF isolates bit 0.13 and relies on the results of the auto-negotiation process to

establish the data rate.

– Disabled, bit 0.13 determines the data rate. In this case, setting bit 0.13 to logic:

• Zero selects 10-Mbps ICS1893AF operations.

• One selects 100-Mbps ICS1893AF operations.

8.2.4

Auto-Negotiation Enable (bit 0.12)

This bit provides a means of controlling the ICS1893AF Auto-Negotiation sublayer. Its operation depends

on the HW/SW input pin.

When the ICS1893AF is configured for:

• Hardware mode, (that is, the HW/SW pin is logic zero), the ICS1893AF isolates bit 0.12 and uses the

ANSEL (Auto-Negotiation Select) input pin to determine whether to enable the Auto-Negotiation

sublayer.

Note:

In Hardware mode, bit 0.12 is undefined.

• Software mode, (that is, the HW/SW pin is logic one), bit 0.12 determines whether to enable the

Auto-Negotiation sublayer. When bit 0.12 is logic:

– Zero:

• The ICS1893AF disables the Auto-Negotiation sublayer.

• The ICS1893AF bit 0.13 (the Data Rate bit) and bit 0.8 (the Duplex Mode bit) determine the data

rate and the duplex mode.

– One:

• The ICS1893AF enables the Auto-Negotiation sublayer.

• The ICS1893AF isolates bit 0.13 and bit 0.8.

ICS1893AF 数据表(PDF) 60 Page - Renesas Technology Corp

ICS1893AF 数据表(HTML) 60 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载