ICS1893AFILF datasheet(52/137 Pages) RENESAS

52 / 137 page

ICS1893AF, Rev D 10/26/04

October, 2004

Chapter 7

Functional Blocks

ICS1893AF Data Sheet - Release

7.6

Functional Block: Management Interface

As part of the MAC/Repeater Interface, the ICS1893AF provides a two-wire serial management interface

which complies with the ISO/IEC 8802-3 standard MII Serial Management Interface. This interface is used

to exchange control, status, and configuration information between a Station Management entity (STA) and

the physical layer device (PHY). The PHY and STA exchange this data through a pre-defined set of

management registers. The ISO/IEC standard specifies the following components of this serial

management interface:

• A set of registers (Section 7.6.1, “Management Register Set Summary”)

• The frame structure (Section 7.6.2, “Management Frame Structure”)

• The protocol

In compliance with the ISO/IEC specification, the ICS1893AF implementation of the serial management

interface provides a bi-directional data pin (MDIO) along with a clock (MDC) for synchronizing the

exchange of data. These pins remain active in all ICS1893AF MAC/Repeater Interface modes (that is, the

10/100 MII, 100M Symbol, and 10M Serial interface modes).

7.6.1

Management Register Set Summary

The ICS1893AF implements a Management Register set that adheres to the ISO/IEC standard. This

Control and Status registers and the ISO/IEC ‘Extended’ registers as well as some ICS-specific registers.

7.6.2

Management Frame Structure

The Serial Management Interface is a synchronous, bi-directional, two-wire, serial interface for the

exchange of configuration, control, and status data between a PHY, such as an ICS1893AF, and an STA.

All data transferred on an MDIO signal is synchronized by its MDC signal. The PHY and STA exchange

data through a pre-defined register set.

The ICS1893AF complies with the ISO/IEC defined Management Frame Structure and protocol. This

structure supports both read and write operations. Table 7-2 summarizes the Management Frame

Structure.

Note:

The Management Frame Structure starts from and returns to an IDLE condition. However, the IDLE

periods are not part of the Management Frame Structure.

Table 7-2.

Management Frame Structure Summary

Frame Field

Data

Comment

Acronym

Frame Function

PRE

Preamble (Bit 1.6)

11..11

32 ones

SFD

Start of Frame

2 bits

Operation Code

10/01 (read/write)

2 bits

PHYAD

PHY Address (Bits 16.10:6)

AAAAA

5 bits

REGAD

RRRRR

5 bits

Turnaround

Z0/10 (read/write)

2 bits

DATA

Data

DDD..DD

16 bits

ICS1893AFILF 数据表(PDF) 52 Page - Renesas Technology Corp

ICS1893AFILF 数据表(HTML) 52 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载

链接网址

ICS1893AFILF 数据表(PDF) 52 Page - Renesas Technology Corp

ICS1893AFILF 数据表(HTML) 52 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表 下载

链接网址

数据表下载