AD5522JSVDZ datasheet(16/45 Pages) AD

16 / 45 page

AD5522

Preliminary Technical Data

Rev. PrL | Page 16 of 45

FUNCTIONAL DESCRIPTION

The AD5522 is a highly integrated quad per pin parametric

measurement unit (PPMU) for use in semiconductor automatic

test equipment. It contains programmable modes to force a pin

voltage and measure the corresponding current (FVMI), force

current measure voltage (FIMV), force current measure current

(FIMI), force voltage measure voltage (FVMV) and force

nothing measure voltage (FNMV) or measure current (FNMI).

The PPMU can force or measure a voltage range of 22.5 V. It

can force or measure currents ranging up to 64mA per channel

using the internal amplifier, while the addition of an external

amplifier enables higher current ranges. On Chip are all the

DAC levels required for each PMU channel.

FORCE AMPLIFIER

The force amplifier drives the analog output FOH, which drives

a programmed current or voltage to the DUT (device under

test). Headroom and footroom requirements for this amplifier

is 3V on either end. An additional ±1V is dropped across the

sense resistor when maximum current is flowing through it.

This amplifier is designed to drive DUT capacitances up to

10nF, with a compensation value of 100pF. Larger DUT

capacitive load will require larger compensation capacitances.

Local feedback ensures the amplifiers are stable when disabled.

A disabled channel reduces power consumption by

2.5mA/channel.

COMPARATORS

Per channel, the DUT measured value is monitored by two

comparators configured as window comparators. Internal DAC

levels set the CPL and CPH (low and high) threshold values.

There are no restrictions on the voltage settings of the

comparator high and lows. CPL going higher than CPH is not a

useful operation; however, it will not cause any problems to the

device. CPOL and CPOH are continuous time comparator

outputs.

Table 7. Comparator Output Function

TEST CONDITION

CPOL

CPOH

VDUT or IDUT > CPH

VDUT or IDUT < CPH

VDUT or IDUT > CPL

VDUT or IDUT < CPL

CPH > VDUT or IDUT > CPL

When using SPI interface, full comparator functionality is

available. When using the LVDS interface, the comparator

function is limited to one output per comparator, due to the

large pin count requirement of the LVDS interface. In this case,

comparator output available CPO (0-3) provides information

on whether the measured voltage or current is inside or outside

the set CPH and CPL window. Information of whether the

measurement was high or low is available via the serial

interfaces (Comparator Status Register).

Table 8. Comparator Output Function using LVDS interface

TEST CONDITION

CPO Output

CPL < VDUT And IDUT < CPH

CPL > VDUT or IDUT > CPH

CLAMPS

Current and voltage clamps are included on chip per PMU

channel. They protect the DUT in the event of an open or a

short. Internal DAC levels set the CLL and CLH (low and high)

levels and the clamps work to limit the force amplifier in the

event of a voltage or current at the DUT exceeding the set levels.

The clamps also function to protect the DUT when a transient

voltage or current spike occurs when changing to a different

operating mode or when programming the device to a different

current range.

The voltage clamps are active while forcing current and the

current clamps are active while forcing voltage. By default, the

current clamps are off. Simply set them up via the status register

through the serial interface.

If a clamp level has been hit, this will be flagged via the CGALM

open drain output and the resulting alarm information may be

read back via the SPI or LVDS interface. CLL should never be

greater than CLH.

AD5522JSVDZ 数据表(PDF) 16 Page - Analog Devices

AD5522JSVDZ 数据表(HTML) 16 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45

数据表下载