GWIXC1100BCT datasheet(23/134 Pages) INTEL

23 / 134 page

Intel® IXP42X Product Line of Network Processors and IXC1100 Control Plane Processor

Datasheet

March 2005

Document Number: 252479, Revision: 005

2.1.4

UTOPIA 2

The integrated, UTOPIA-2 interface works with a network processing engine, for several of the

IXP42X product line and IXC1100 control plane processors. (See Table 4 on page 20.)

The UTOPIA-2 interface supports a single- or a multiple-physical-interface configuration with

cell-level or octet-level handshaking. The network processing engine handles segmentation and

reassembly of ATM cells, CRC checking/generation, and transfer of data to/from memory. This

allows parallel processing of data traffic on the UTOPIA-2 interface, off-loading processor

overhead required by the Intel XScale® Core.

The IXP42X product line and IXC1100 control plane processors are compliant with the ATM

Forum, UTOPIA Level-2 Specification, Revision 1.0.

2.1.5

USB Interface

The integrated USB 1.1 interface is a device-only controller. The interface supports full-speed

operation and 16 endpoints and includes an integrated transceiver.

There are:

• Six isochronous endpoints (three input and three output)

• One control endpoints

• Three interrupt endpoints

• Six bulk endpoints (three input and three output)

2.1.6

PCI Controller

The IXP42X product line and IXC1100 control plane processors’ PCI controller is compatible with

the PCI Local Bus Specification, Rev. 2.2. The PCI interface is 32-bit compatible bus and capable

of operating as either a host or an option (i.e., not the Host) For more information on PCI

Controller support and configuration see the Intel® IXP42X Product Line of Network Processors

and IXC1100 Control Plane Processor Developer’s Manual.

2.1.7

SDRAM Controller

The memory controller manages the interface to external SDRAM memory chips. The interface:

• Operates at 133.32 MHz (which is 4 * OSC_IN input pin.)

• Supports eight open pages simultaneously

• Has two banks to support memory configurations from 8 Mbyte to 256 Mbyte

The memory controller only supports 32-bit memory. If a x16 memory chip is used, a minimum of

two memory chips would be required to facilitate the 32-bit interface required by the IXP42X

product line and IXC1100 control plane processors. A maximum of four SDRAM memory chips

may be attached to the processors. For more information on SDRAM support and configuration see

the Intel® IXP42X Product Line of Network Processors and IXC1100 Control Plane Processor

Developer’s Manual.

The memory controller internally interfaces to the North AHB and South AHB with independent

interfaces. This architecture allows SDRAM transfers to be interleaved and pipelined to achieve

maximum possible efficiency.

GWIXC1100BCT 数据表(PDF) 23 Page - Intel Corporation

GWIXC1100BCT 数据表(HTML) 23 Page - Intel Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载