GWIXC1100BCT datasheet(24/134 Pages) INTEL

24 / 134 page

Intel® IXP42X Product Line of Network Processors and IXC1100 Control Plane Processor

March 2005

Datasheet

Document Number: 252479, Revision: 005

The maximum burst size supported to the SDRAM interface is eight 32-bit words. This burst size

allows the best efficiency/fairness performance between accesses from the North AHB and the

South AHB.

2.1.8

Expansion Bus

The expansion interface allows easy and — in most cases — glue-less connection to peripheral

devices. It also provides input information for device configuration after reset. Some of the

peripheral device types are flash, ATM control interfaces, and DSPs used for voice applications.

(Some voice configurations can be supported by the HSS interfaces and the Intel XScale® Core,

implementing voice-compression algorithms.)

The expansion bus interface is a 16-bit interface that allows an address range of 512 bytes to

16 Mbytes, using 24 address lines for each of the eight independent chip selects.

Accesses to the expansion bus interface consists of five phases. Each of the five phases can be

lengthened or shortened by setting various configuration registers on a per-chip-select basis. This

feature allows the IXP42X product line and IXC1100 control plane processors to connect to a wide

variety of peripheral devices with varying speeds.

The expansion bus interface supports Intel or Motorola* microprocessor-style bus cycles. The bus

cycles can be configured to be multiplexed address/data cycles or separate address/data cycles for

each of the eight chip-selects.

Additionally, Chip Selects 4 through 7 can be configured to support Texas Instruments HPI-8 or

HPI-16 style accesses for DSPs.

The expansion bus interface is an asynchronous interface to externally connected chips. However,

a clock must be supplied to the IXP42X product line and IXC1100 control plane processors’

expansion bus interface for the interface to operate. This clock can be driven from GPIO 15 or an

external source. The maximum clock rate that the expansion bus interface can accept is

66.66 MHz.

At the de-assertion of reset, the 24-bit address bus is used to capture configuration information

from the levels that are applied to the pins at this time. External pull-up/pull-down resistors are

used to tie the signals to particular logic levels. (For additional details, see “Package and Pinout

Information” on page 50.)

2.1.9

High-Speed, Serial Interfaces

The high-speed, serial interfaces are six-signal interfaces that support serial transfer speeds from

512 KHz to 8.192 MHz, for some models of the IXP42X product line and IXC1100 control plane

processors. (See Table 4 on page 20.)

Each interface allows direct connection of up to four T1/E1 framers and CODEC/SLICs to the

IXP42X product line and IXC1100 control plane processors. The high-speed, serial interfaces are

capable of supporting various protocols, based on the implementation of the code developed for the

network processor engine core. For a list of supported protocols, see the Intel® IXP400 Software

Programmer’s Guide.

GWIXC1100BCT 数据表(PDF) 24 Page - Intel Corporation

GWIXC1100BCT 数据表(HTML) 24 Page - Intel Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载