GWIXC1100BCT datasheet(36/134 Pages) INTEL

36 / 134 page

Intel® IXP42X Product Line of Network Processors and IXC1100 Control Plane Processor

March 2005

Datasheet

Document Number: 252479, Revision: 005

Table 7.

PCI Controller (Sheet 1 of 2)

Name

Power

Reset1

Reset2 Type†

Description

PCI_AD[31:0]

I/O

PCI Address/Data bus used to transfer address and bidirectional

data to and from multiple PCI devices.

Should be pulled low with a 10-K

Ω resistor when not being

utilized in the system.

PCI_CBE_N[3:0]

I/O

PCI Command/Byte Enables is used as a command word during

PCI address cycles and as byte enables for data cycles.

Should be pulled high with a 10-K

Ω resistor when not being

utilized in the system.

PCI_PAR

I/O

PCI Parity used to check parity across the 32 bits of PCI_AD and

the four bits of PCI_CBE_N.

Should be pulled low with a 10-K

Ω resistor when not being

utilized in the system.

PCI_FRAME_N

I/O

PCI Cycle Frame used to signify the beginning and duration of a

transaction. The signal will be inactive prior to or during the final

data phase of a given transaction.

Should be pulled high with a 10-K

Ω resistor when not being

utilized in the system.

PCI_TRDY_N

I/O

PCI Target Ready informs that the target of the PCI bus is ready

to complete the current data phase of a given transaction.

Should be pulled high with a 10-K

Ω resistor when not being

utilized in the system.

PCI_IRDY_N

I/O

PCI Initiator Ready informs the PCI bus that the initiator is ready

to complete the transaction.

Should be pulled high with a 10-K

Ω resistor when not being

utilized in the system.

PCI_STOP_N

I/O

PCI Stop indicates that the current target is requesting the

current initiator to stop the current transaction.

Should be pulled high with a 10-K

Ω resistor when not being

utilized in the system.

PCI_PERR_N

I/O

PCI Parity Error asserted when a PCI parity error is detected —

between the PCI_PAR and associated information on the

PCI_AD bus and PCI_CBE_N — during all PCI transactions,

except for Special Cycles. The agent receiving data will drive this

signal.

Should be pulled high with a 10-K

Ω resistor when not being

utilized in the system.

PCI_SERR_N

I/OD

PCI System Error asserted when a parity error occurs on special

cycles or any other error that will cause the PCI bus not to

function properly. This signal can function as an input or an open

drain output.

Should be pulled high with a 10-K

Ω resistor when not being

utilized in the system.

While PWRON_RESET_N is deasserted use Power On Reset column for the pin state.

After deassertion of PWRON_RESET_N, and deassertion of RESET_IN_N, and assertion of

PLL_LOCK, all signals reflect the value shown in the RESET column.

†

For a legend of the Type codes, see Table 5 on page 33.

GWIXC1100BCT 数据表(PDF) 36 Page - Intel Corporation

GWIXC1100BCT 数据表(HTML) 36 Page - Intel Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载

链接网址

GWIXC1100BCT 数据表(PDF) 36 Page - Intel Corporation

GWIXC1100BCT 数据表(HTML) 36 Page - Intel Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表 下载

链接网址

数据表下载