AM29PDS322D datasheet(31/51 Pages) AMD

31 / 51 page

December 4, 2006 23569A5

Am29PDS322D

D A TA

SH EET

DQ2: Toggle Bit II

The “Toggle Bit II” on DQ2, when used with DQ6, indi-

cates whether a particular sector is actively erasing

(that is, the Embedded Erase algorithm is in progress),

or whether that sector is erase-suspended. Toggle Bit

II is valid after the rising edge of the final WE# pulse in

the command sequence.

DQ2 toggles when the system reads at addresses

within those sectors that have been selected for era-

sure. (The system may use either OE# or CE# to con-

trol the read cycles.) But DQ2 cannot distinguish

whether the sector is actively erasing or is erase-sus-

pended. DQ6, by comparison, indicates whether the

device is actively erasing, or is in Erase Suspend, but

cannot distinguish which sectors are selected for era-

sure. Thus, both status bits are required for sector and

mode information. Refer to Table 11 to compare out-

puts for DQ2 and DQ6.

Figure 8 shows the toggle bit algorithm in flowchart

form, and the section “DQ2: Toggle Bit II” explains the

algorithm. See also the DQ6: Toggle Bit I subsection.

Figure 23 shows the toggle bit timing diagram. Figure

24 shows the differences between DQ2 and DQ6 in

graphical form.

Reading Toggle Bits DQ6/DQ2

Refer to Figure 8 for the following discussion. When-

ever the system initially begins reading toggle bit sta-

tus, it must read DQ7–DQ0 at least twice in a row to

determine whether a toggle bit is toggling. Typically,

the system would note and store the value of the tog-

gle bit after the first read. After the second read, the

system would compare the new value of the toggle bit

with the first. If the toggle bit is not toggling, the device

has completed the program or erase operation. The

system can read array data on DQ7–DQ0 on the fol-

lowing read cycle.

However, if after the initial two read cycles, the system

determines that the toggle bit is still toggling, the sys-

tem also should note whether the value of DQ5 is high

(see the section on DQ5). If it is, the system should

then determine again whether the toggle bit is tog-

gling, since the toggle bit may have stopped toggling

just as DQ5 went high. If the toggle bit is no longer

toggling, the device has successfully completed the

program or erase operation. If it is still toggling, the de-

vice did not completed the operation successfully, and

the system must write the reset command to return to

reading array data.

The remaining scenario is that the system initially de-

termines that the toggle bit is toggling and DQ5 has

not gone high. The system may continue to monitor

the toggle bit and DQ5 through successive read cy-

cles, determining the status as described in the previ-

ous paragraph. Alternatively, it may choose to perform

other system tasks. In this case, the system must start

at the beginning of the algorithm when it returns to de-

termine the status of the operation (top of Figure 8).

DQ5: Exceeded Timing Limits

DQ5 indicates whether the program or erase time has

exceeded a specified internal pulse count limit. Under these

conditions DQ5 produces a “1,” indicating that the program

or erase cycle was not successfully completed.

The device may output a “1” on DQ5 if the system tries

to program a “1” to a location that was previously pro-

grammed to “0.” Only an erase operation can

change a “0” back to a “1.” Under this condition, the

device halts the operation, and when the timing limit

has been exceeded, DQ5 produces a “1.”

Under both these conditions, the system must write

the reset command to return to the read mode (or to

the erase-suspend-read mode if the device was previ-

ously in the erase-suspend-program mode).

DQ3: Sector Erase Timer

After writing a sector erase command sequence, the

system may read DQ3 to determine whether or not

erasure has begun. (The sector erase timer does not

apply to the chip erase command.) If additional

sectors are selected for erasure, the entire time-out

also applies after each additional sector erase com-

mand. When the time-out period is complete, DQ3

switches from a “0” to a “1.” If the time between addi-

tional sector erase commands from the system can be

assumed to be less than 50 µs, the system need not

monitor DQ3. See also the Sector Erase Command

Sequence section.

After the sector erase command is written, the system

should read the status of DQ7 (Data# Polling) or DQ6

(Toggle Bit I) to ensure that the device has accepted

the command sequence, and then read DQ3. If DQ3 is

“1,” the Embedded Erase algorithm has begun; all fur-

ther commands (except Erase Suspend) are ignored

until the erase operation is complete. If DQ3 is “0,” the

device will accept additional sector erase commands.

To ensure the command has been accepted, the sys-

tem software should check the status of DQ3 prior to

and following each subsequent sector erase com-

mand. If DQ3 is high on the second status check, the

last command might not have been accepted.

Table 11 shows the status of DQ3 relative to the other

status bits.

AM29PDS322D 数据表(PDF) 31 Page - Advanced Micro Devices

AM29PDS322D 数据表(HTML) 31 Page - Advanced Micro Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51

数据表下载